My Orders
Caloric Range Switches
GET YOUR OFFICIAL Caloric PARTS TO ENSURE VICTORY
Shop By Part Type
View MorePopular Caloric Range Switches
When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner.
When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner.
Installation Instructions
Richard from Lansing, MI
Ignitor did not spark when turning the know
Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that atta
... Read more
ch to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.
Read less
Installation Instructions
RICHARD from PARADISE, TX
Small burner full hot all the time.
TURNED OFF POWER TO STOVE Removed 5 Knobs, 2 screws that held bad switch.
Removed 4 screws and lifted panel up and forward to expose switches. Adjusted spring tension on knob stem to hold knob ( stem in new switch slightly smaller) removed wire from defective switch one at a time and fastened to new switch in sequence. Re ... Read more assembled and turned power on. Defective switch had stuck contacts making it full hot.
Removed 4 screws and lifted panel up and forward to expose switches. Adjusted spring tension on knob stem to hold knob ( stem in new switch slightly smaller) removed wire from defective switch one at a time and fastened to new switch in sequence. Re ... Read more assembled and turned power on. Defective switch had stuck contacts making it full hot.
Read less
Proper control of an electric burner depends on the infinite switch working correctly. A failed switch may keep the element from heating, prevent it from shutting off, or hold it at one temperature. Check the element and connections before ordering a replacement. Match the switch to the complete range model and burner location because similar switches may have different ratings. Disconnect power at the breaker, confirm the appliance is not live, and have a qualified technician complete the repair if the wiring is unclear.
Proper control of an electric burner depends on the infinite switch working correctly. A failed switch may keep the element from heating, prevent it from shutting off, or hold it at one temperature. Check the element and connections before ordering a replacement. Match the switch to the complete range model and burner location because similar switches may have different ratings. Disconnect power at the breaker, confirm the appliance is not live, and have a qualified technician complete the repair if the wiring is unclear.
Installation Instructions
erik from chester springs, PA
The infinite switch controlling one of the range top burners failed.
1 - Turned off electricity to the cook top.
2 - Removed the range top from the cutout in the counter.
3 - Removed the smooth top by removing the screws around the perimiter of the smooth top.
4 - Removed the screws securing the corner closest to the dead switch.
5 - Removed the screws holding the channel, onto which th ... Read more e infinite switched were attached, to the frame of the cooktop base.
6 - Removed the dead switch by removing the screws that hold it to the channel.
7 - One by one move the wires from the old switch to the new one.
8 - Reversed the process, 6 - 5 - 4 - 3 - 2 - 1, to put the cook top back together.
All in all the part was an exact replacement and the repair went really well.
2 - Removed the range top from the cutout in the counter.
3 - Removed the smooth top by removing the screws around the perimiter of the smooth top.
4 - Removed the screws securing the corner closest to the dead switch.
5 - Removed the screws holding the channel, onto which th ... Read more e infinite switched were attached, to the frame of the cooktop base.
6 - Removed the dead switch by removing the screws that hold it to the channel.
7 - One by one move the wires from the old switch to the new one.
8 - Reversed the process, 6 - 5 - 4 - 3 - 2 - 1, to put the cook top back together.
All in all the part was an exact replacement and the repair went really well.
Read less
A black rocker switch gives the user simple on-and-off control from the appliance panel. Depending on the appliance, it may operate an oven light or an exhaust fan. Pressing either side of the switch opens or closes the electrical circuit. Replacement may be needed if the switch sticks, feels loose, or no longer turns the connected feature on. Shut off electrical power at the breaker or unplug the appliance before beginning the repair. Wear work gloves and label each wire before disconnecting the old switch.
A black rocker switch gives the user simple on-and-off control from the appliance panel. Depending on the appliance, it may operate an oven light or an exhaust fan. Pressing either side of the switch opens or closes the electrical circuit. Replacement may be needed if the switch sticks, feels loose, or no longer turns the connected feature on. Shut off electrical power at the breaker or unplug the appliance before beginning the repair. Wear work gloves and label each wire before disconnecting the old switch.
Installation Instructions
Al from Abbeville, AL
The switch on the exhaust fan for the grill part of the stove went bad. I found the part on your site easily , ordered it and got it within 4 days.
I simply looked at the new switch , to see how it fastened in the stove. It had plastic clips that were easily depressed to allow the swithch to be removed. I removed it , (after turning the circuit breaker off to the stove) removed the three wires , and replace them on the new switch and simply pushed it in the space. It snapped in place
... Read more
, and the job was done . Works great!
Read less
This switch controls the stove top surface burner.
This switch controls the stove top surface burner.
Installation Instructions
Don from Sacramento, CA
replaced warn out switch
fours screws for rangetop, two for the switch. The only tricky part was two terminals had swappped places with each other. Looking at the enclosed schematic sent with the switch, a neighbor & I figured out what was wrong. Switched the two leads and done!
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
Selector switch
Selector switch
Switch
Switch
Switch, ignition
Switch, ignition