Amana Air Conditioner Hardware

Your Price

$7.76

Screw, 8/18 x 3/8

★★★★★

2 Reviews

PartSelect Number PS11746840

Manufacturer Part Number WP90767

This screw is sold individually.

Installation Instructions

Alexander from Lakeland, FL

Broken Dryer Knob

First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing pointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!! Read more...

Videos!

Your Price

$10.83

Hose Clamp

★★★★★

2 Reviews

PartSelect Number PS11740613

Manufacturer Part Number WP285655

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

Fixes these symptoms

Leaking
Will not drain
See more...

Installation Instructions

Stephen from Laveen, AZ

Drive Pump Leaked

It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on. Read more...

Your Price

$7.84

Screw

PartSelect Number PS11757438

Manufacturer Part Number WPY014874

Sold Individually.

Installation Instructions

Gene from Virginia Beach, VA

Dryer made loud screeching noise.

After reading all the other repair stories on Partselect, by the way thank you all, I removed the door, then removed the two security hooks that hold the top secure. Then I removed the front panel. I then marked all the screws on the outer door and shroud so I could easily put it back together. I left the all the wires connected and set the shroud and outer door to the side and removed the drum belt and drum. Removed the spring off the idler arm, then using nutdriver, removed the screw that secures the idler arm to the motor. Assembled the new idler arm parts and reversed the process to put it all back together. If I would have replaced the idler arm assembly the same time I replaced the drum support rollers, I wouldn't have had to do this twice! But now I am an expert repair tech on this particular model. Read more...

Your Price

$7.84

Screw

PartSelect Number PS11742742

Manufacturer Part Number WP489349

This screw is sold individually.

Your Price

$7.76

Screw

★★★★★

5 Reviews

PartSelect Number PS11753384

Manufacturer Part Number WPW10348409

Sold individually.

Installation Instructions

REBECCA from GREENFIELD TWP., PA

My son broke the door handle off the Refrigerator

I removed two screws that were holding on broken handle. I put new handle in place and attached it with new screws. Ordering parts on line and receving them in mail a few days later was awsome. I did not need my husbands help at all . Read more...

Your Price

$7.76

Screw

★★★★★

2 Reviews

PartSelect Number PS11747542

Manufacturer Part Number WP98165

This screw is a little under an inch long and is made of metal. It is used with a refrigerator's ice maker assembly. Sold individually.

Installation Instructions

Lynn H from MILL CREEK, WA

Hinge pin for drawer lid broke

1. Remove all drawers {3}, shelves {glass 1}, shelf support {1}. 2. Remove two {2} screws from End Cap. 3. Carefully remove End Cap and drawer temperature control part on the back wall keeping them aligned as installed. The part on the back wall swings out so that the tab on the left end of the piece may be withdrawn from the securing slot (hole). The two parts should be carefully removed while keeping the two parts at a right angle the way they are installed. The reason for this caution follows. 4. On the back side of both parts are plastic pieces that, I believe, can be easily broken if you are not aware. The pieces are connected together at the right angle. They are the control arms for the temperature control -- on right side End Cap only -- the left side doesn't have them or the rear part on the back wall. 5. The pieces must be disconnected and removed. You must examine and ponder how they are held in place and hooked together in order to disconnect and remove them without damaging them. The same advice is applicable to reinstalling the pieces in the new part -- End Cap. 6. After reassembled and keeping the two parts at a right angle, insert the tab on the left end of the back wall part into the slot (hole) and swing the two parts back into position. 7. Replace the screws. 8. Done, reinstall the shelf, shelf support, and the drawers. NOTE: I ordered the two screws but they were not needed. Read more...

Your Price

$7.76

Appliance Screw

PartSelect Number PS11743002

Manufacturer Part Number WP59002061

Sold individually.

Installation Instructions

John from WAKEFIELD, MA

Flames appeared outside of burners

The front burner had a noticible flame coming from the base, so I originally purchased a single burner to replace it (you could see a corroded hole at the bottom). Upon taking the unit apart, I noticed the corrosion was much worse than met the eye. Given the age of the unit and that some parts were already becoming discontinued I decided to gut the whole thing and replace it all.
The burner unit slides out easily and after unscrewing the sides, you have to disconnect the wires from the underside of the igniters. The venturi tubes and igniters then unscrew from the underside of the burners which twist right out of the assembly. Re-Assembly is very intuitive looking at it and it all goes right back together as it came out. Took 45 minutes total and that includes fighting with some screws that had rusted onto the burner.
Reading some of the previous reviews, current prices are double to triple what other people did the repair for leading me to believe parts won't be available for much longer. Make the repair while you still can! Read more...