Airstream Parts

This is a Powermate, Southland, and Airstream replacement part directly sourced from the manufacturer for use in edgers. The air cleaner cover goes next to the air cleaner element. It might require a screwdriver and a socket set to replace this item. It will need to be replaced if it breaks. This part is made of a durable material and is available individually.

This housing is what directly connects the rest of the air filter housing to the equipment. This genuine OEM part is made of high-quality plastic and is compatible with several different models of edgers, but the hardware to fasten this housing to your equipment is sold separately. If there are any cracks or the fit and seal for the air filter housing is not tight enough, the housing will need to be replaced because it seals dust, dirt, and debris from entering your equipment, ensuring better health and performance. The cleaner your air filter, the better and longer your equipment will run and stay running, without need for costlier repairs. This housing is typically fastened to the side of the engine but consult with the user manual for your model for the appropriate installation location.

It is a genuine manufacturer-supplied item that is made for use with Powermate, Southland and Airstream lawn edgers. This item provides an identical replacement for a damaged or a missing drive shaft assembly that was installed on a new unit. Check the owner's manual and the diagrams for your model to ensure the correct repair procedure. Note, this high-quality assembly is made of durable metal and is sold individually. A wrench set and pliers might be needed when replacing this component.

This starter assembly is a recoil mechanism with a pulley, starter rope, handle, guide pan and springs; everything you need to efficiently start your equipment. This starter assembly is designed for and compatible with various models of edgers and is sold as an individual OEM assembly, without any securing hardware like screws. Starter assemblies can break, wear out, and eventually need replacing because they are a high-use part, and this can show in areas such as starter ropes breaking or fraying, recoil springs not holding the same level of tension, or if a smaller, more complex component within the assembly is not working properly anymore. If you notice that your edger is not starting easily, has starting issues, or the engine simply no longer cranks ? those are signs that the starter assembly needs replacing. This replacement process is as simple as unscrewing the securing screws from the old starter assembly from the cylinder head part of your edger and securing the new starter assembly in its place.

This OEM-approved air cleaner gasket creates a seal between the air cleaner housing and the carburetor in your lawn and garden equipment. It makes sure that only clean air enters the engine for combustion. Over time, the gasket wears out. It may appear cracked, flattened, or distorted. You need to replace a damaged gasket. Otherwise, air leaks can happen, and debris and contaminants can enter the engine. This leads to reduced engine efficiency, rough running, and even engine stalling. If you are replacing your gasket, remove the spark plug first. You then need to access the air cleaner housing by removing its cover with a screwdriver. You can then peel off the gasket from the housing. This replacement part is sold individually.

This is a genuine replacement part sourced from the original manufacturer for use with edgers, sanders, and miter saws. The special ball bearing is commonly used to reduce friction between a rotating shaft and fixed part assembly. This ball bearing is available as an individual replacement please see model diagram for associative parts.

This sustain board is used to keep the filter in the correct position within the air filter housing for a variety of different edgers. Made of plastic and sold as an individual part, this sustain board also serves the purpose of creating a better seal within the housing. Before replacing this sustain board, check to ensure the filter is clean and not clogged, and that the rest of the housing is intact. To replace the sustain board, simply unscrew, disconnect and remove the cover for the housing, the air filter, and the old sustain board, before installing the new board, the filter, and the cover.

It is a genuine item that is supplied by the original equipment manufacturer for use with lawn edgers. This is an identical replacement for a missing or a faulty hose that is utilized to deliver the fuel. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality part is made of durable rubber and is sold individually. Note, the #A100624 Clamp, Fuel Line is sold separately.

This is a genuine OEM replacement part specifically designed for lawn edgers. The belt, made of rubber, has a length of 56 inches and a width of 1/2 inch. Note that your previous belt may appear longer than this due to stretching and wear over time. Its primary function is to connect the motor to the blade, enabling the blade to spin and efficiently cut grass. If you notice signs of fraying, tearing, or hear squeaking and grinding noises while operating the edger, it indicates that the belt is no longer functioning as it should and should be replaced. When removing the damaged belt, take note of how it is threaded around the pulleys to ensure that you install it the correct way. The belt is crucial to the performance of the edger; therefore, it is important to regularly inspect the belt and replace it when necessary.

This is a genuine manufacturer-approved part that is specially made for use with Southland and Airstream handheld lawn and garden equipment. It is designed to keep the fuel in the tank, unfortunately, over time it may wear out and begin to fail eventually requiring a replacement. It includes a retainer that remains in the tank to keep the fuel cap from being lost or falling on the ground. Keep in mind it is made of high-quality plastic and is sold individually. Please make sure to check the appropriate diagrams of your model for the correct location and application of this part.