This easy-to-install water filter improves the taste and quality of your fridge’s water by reducing lead, VOCs, and over 50 other impurities. NSF-certified for performance, it’s located in the upper-right corner and should be replaced every six months for best results.
This evaporator fan motor circulates air to the fresh food compartments for efficient cooling. It powers the evaporator fan that draws air from the refrigerator and circulates it over the evaporator coils. Your fan motor has a long life cycle, but can burn out quickly if there is an obstruction preventing the fan from rotating. If the fa...Read moren does not operate, the freezer will not cool properly. This will affect the performance of the compressor. This evaporator fan motor is located in the back of the freezer section of your refrigerator, behind the auger motor assembly. It is attached to the back wall. If you notice problems with your freezer then check to see if there is anything blocking a fan blade. If there is no obstruction, test the evaporator fan motor using a multimeter. Test the 2 wires that travel from the coil on the motor for resistance. If these tests indicate that the evaporator fan motor is at fault, it must be replaced. This part features 1 evaporator fan motor, which is metal and plastic, and comes in white/silver
This evaporator fan blade is for your refrigerator, and it circulates air so that the temperature of the fridge is regulated. This model has 3 blades, and is a little more than 4 inches in diameter. It is made of white plastic and is sold individually. If your refrigerator is noisy and you hear a clicking sound, it is a good indication th...Read moreat the evaporator fan blade is warped or damaged. If the fridge or freezer sections become too warm, the fan could be to blame as well.
This is a replacement evaporator fan grommet for your refrigerator. The fan grommet absorbs the vibration from the evaporator fan motor for quiet operation while it runs. If your evaporator fan is unusually noisy, it could be because the grommet is damaged. This grommet is made of grey plastic and is approximately one inch in diameter. To...Read more access the fan grommet and complete this repair, you will need to remove the evaporator fan motor assembly. This part is sold individually.
This bypass filter plug is an authentic OEM replacement part designed for your refrigerator. It is small component that is used in the water filtration system. It creates a direct path for water to flow without going through the filter, ensuring that the water dispenser and ice maker continue to function even when the filter is not in use...Read more. If the filter is old or clogged and needs replacement, or if you prefer not to use a filter for any reason, you can insert the bypass filter plug into the filter housing to continue using your fridge.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Evaporator motor sounded like wind in the trees howling
112 of 139 peoplefound this instruction helpful.
DOUG from MARYSVILLE, OH
A Bit Difficult
30 - 60 mins
Nutdriver, Screw drivers
I had to remove all of the shelves.....part of the ice maker.....the rear cover over the freezer coils.....There were two wires that came from the back of the freezer that were also incorporated with the fan motor plug from the factory....This caused me to cut all of the wires from the new motor and soider them to the existing plug and sh
... Read morerink wrap the connections. If GE would have supplied two new ends I could have cut only those wires added the ends and inserted them into the new motor plug thus eliminating an extra hour and a soildering iron,,,,In my case not a big deal however not a project for those who have trouble with repairs using these type of tools.
Read less
Was this helpful?
Thank you for voting!
The evaporator fan motor stopped running, freezer was warmer than normal
66 of 88 peoplefound this instruction helpful.
David from Romeo, MI
Really Easy
15 - 30 mins
Nutdriver, Pliers
First ,I placed all the frozen food from the freezer into the lower fridge compartment. Removed the main shelf. Removed the ice cube tray shelf. Removed the center plastic covers using a nut driver. Removed the complete inside back wall of the freezer to get access to the fan. Simply removed about 5 screws, and cut 3 tie straps that held
... Read morethe wiring in place. Unplugged the fan connector and removed fan with its brackets and placed them on the kitchen table. Then used the nut driver to remove 2 screws which hald the fan to its bracket. Simply pulled off the fan blades and pressed them onto the new motor. Mounted new motor onto the bracket. Reinstalled the fan assembly back into freezer. Reconnected the wiring and the fan began to run... BE CAREFUL NOT TO TOUCH THE FAN WITH YOUR FINGERS! Finally replaced all the covers, panels, and shelf etc. and everything is once again nice and cold.
Read less
Was this helpful?
Thank you for voting!
Fan motor making noise due to broken fan blade
64 of 93 peoplefound this instruction helpful.
James from Gainesville, VA
Easy
15 - 30 mins
Nutdriver
1) Unplugged fridge and removed cover over light in freezer. 2)Removed screws holding cover over motor. 3) Removed screws on bracket holding motor in place. 4) Un plugged motor and used razor blade to cut grommet holding wires in place. 5) Plugged in new motor and routed wires through grommet. Then used zip ties to hol
... Read mored grommet together. 5) Re-attached motor bracket and installed new fan. 6) Reinstalled cover over motor.