ZGP304NT2SS General Electric Range - Overview

Diagrams for ZGP304NT2SS

See every part. Know exactly what you need.

Part List

Parts for the ZGP304NT2SS

$30.53

Temperature Sensor

★★★★★

(56)

Part #WB21X22134

The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. The function of the oven temperature sensor assembly is to measure the temperature inside your oven while it is on and send the temperature back up to the electronic control, which adjusts as necessary. If your oven is havi...Read more

Read less

$16.05

Door Handle Fastener

★★★★★

(11)

Part #WR01X11007

This is a door handle fastener to secure the handle to your refrigerator drawer. It is also known and a mounting bolt or screw. It is approximately 1 inch in total length, and is made of metal.

$52.47

Burner Cap (18k)

Part #WB29X43469

This burner cap replaces a worn or discolored cap on high-output burners, helping ensure even heat distribution and reliable cooking performance. Designed for 18,000-BTU burners, it’s a direct drop-in replacement and requires no tools for installation. The cap restores both the look and efficiency of the cooktop and is sized at roughly fo...Read more

Read less

$35.80

Range Board Sensor

Part #WB27X28659

$33.69

Screw

Part #WB01K10002

Size: 8-32 inch Sold individually.

$16.23

SPRING IGNITER

Part #WB09T10011

$18.59

NUT

Part #WB02T10017

$39.43

HUB BLADE Assembly

★★★★★

(1)

Part #WB02T10289

$19.50

Screw

Part #WB01X24735

$15.00

Screw

Part #WB01T10104

$16.23

Igniter

Part #WB02T10323

$40.65

Inner Cap (Brass)

Part #WB16X32876

Common Symptoms of the ZGP304NT2SS

How this model fails, and the parts that fix it.

Little to no heat when baking

Fixed by
these parts

Show All

Oven not heating evenly

Element will not heat

Little to no heat when broiling

Fixed by
these parts

Show All

Door won’t open or close

Fixed by
these parts

Show All

Videos related to the ZGP304NT2SS

Watch our pros, then fix it yourself.

Replacing the Temperature Sensor

Repair Tips From Fixers Like You

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Oven would go in to a F2 Error

148 of 226 people found this instruction helpful.

Peter from stamford, CT
Really Easy
15 - 30 mins
Nutdriver

Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.

Was this helpful?

Oven wouldn't preheat above 300 degrees

54 of 95 people found this instruction helpful.

Gerald from Cape Canaveral, FL
Really Easy
15 - 30 mins
Nutdriver

Unplugged appliance and removed 5 screws on back of stove/oven and removed plate. Disconnected the sensor and unscrewed it on the inside of the oven. Pulled the cord through and replaced with new sensor. Replaced all parts and plugged in the appliance and tested. Worked great.

Was this helpful?

I kept getting An F2 error and the temperature did not seem accurate

29 of 38 people found this instruction helpful.

Chad from Bloomington, IN
Really Easy
Less than 15 mins
Screw drivers, Socket set, Wrench (Adjustable), Wrench set

1) pull out the stove
2) remove the 7 sheet metal screws holding the back panel on. (the panel that also covers where the cord splits and connects to the oven.
3) Find the small plastic connector located in the middle of the back of the range and unplug it.
4) open the front of the oven and remove the one screw holding in ... Read more

Read less

Was this helpful?