This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
If your refrigerator or freezer is too warm, or making noises, you may need to replace the fan blade. The fan blade attaches to the evaporator motor, which is in the freezer section, to help circulate the cold air into the refrigerator and freezer sections. The fan blade is white in color and made from plastic. This is a genuine OEM part...Read more. Please be sure to disconnect the power to your refrigerator before starting your repair.
This temperature sensor is for refrigerators.
The temperature sensor senses the temperature inside the refrigerator and sends information to the electronic control.
Unplug the refrigerator and safely store any food that could deteriorate while the power is off before installing this part. Wear work gloves to protect your hands. The ...Read morethermistor itself, part WPW10383615, should test at these Ohms depending on temperature. It's recommended to test at room temperature and again in a glass of ice water to make sure it's sensing temperatures properly. So it should read around 3000 - 5000 Ohms at room temperature 7000 - 10000 Ohms at 0°C and 20000 Ohms at -15°C.
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a pr...Read moreotective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.
The compressor run capacitor helps keep the motor running smoothly in refrigerators. It works with various models and is a genuine replacement part. Always unplug the refrigerator before installing the capacitor, and check the part number for compatibility with your model.
This wire shelf is a genuine OEM replacement part for refrigerators. It has dimensions of approximately 25 inches by 15.5 inches. The wire shelf is positioned within the freezer compartment of your fridge where it provides additional storage space in the freezer. It allows you to eastly arrange and organize various food items and containe...Read morers for maximum efficiency. Over time the shelf may break, crack or become unstable. You should replace the shelf if it is no longer able to support items stored on it, to avoid any accidents or damage.
This is the replacement wire shelf for your refrigerator. It is approximately 12 inches by 25 inches. The wire shelf slides into grooves on either side of the refrigerator and is used to store meat and other food items. The main reason to replace the wire shelf is if yours is cracked, damaged, or missing. To replace the wire shelf, simply...Read more slide the old shelf out, and slide the new one into place. This part is an OEM part sourced directly from the manufacturer, and is sold individually.
This authentic OEM black touch-up paint is specifically designed for repairing minor scratches, chips, or blemishes on your kitchen appliances. The bottle contains 16ml or 0.6oz of black paint and has an applicator brush under the cap, the same way a nail polish bottle is designed. Restoring these visible damages is important because crac...Read moreked or chipped surfaces can become a breeding ground for dirt and bacteria. If your existing bottle of paint has a thick or clumpy consistency, do not use it. Remember to shake the bottle before applying the paint to your appliance. Please keep in mind that this bottle is sold individually.
Food that freezes in the refrigerator may point to a temperature sensor problem. The sensor works like a small thermometer by tracking the temperature inside the compartment. As the temperature changes, it sends a signal that helps the appliance control its cooling cycles. Replacement may be needed if testing shows that the sensor gives t...Read morehe wrong reading or has damaged wires. Disconnect electrical power before opening the appliance. Follow the service guide to find the correct sensor location, and make sure the plug is fully connected during installation.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Scratches in Surface
83 of 227 peoplefound this instruction helpful.
Michelle from Richardson, TX
Really Easy
Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
The freezer wasn't defrosting.
18 of 32 peoplefound this instruction helpful.
Nancy from JAMESTOWN, NY
Very Easy
Less than 15 mins
took the old thermistor out and put the new one in.
Was this helpful?
Thank you for voting!
Fridge would not start
9 of 11 peoplefound this instruction helpful.
Glen from PT CHARLOTTE, FL
Really Easy
15 - 30 mins
Nutdriver
Unplug the fridge then wheel the refrigerator out to where you can get to the back - you will probably have to disconnect the ice maker water hose. Using the nut driver remove all the screws from the lower panel on the fridge. You will not have to remove the water hose connection just move the panel around a little. Look on the left side
... Read more(facing the back of the fridge) you will see the capacitor held onto the compressor with a spring clip. Just pull the clip toward you and that will free the capacitor. Pull up on the capacitor and that will unplug it from the compressor. Be careful not to touch the two poles on the old capacitor. Capacitors store electricity and it could give you a jolt. I used electrical tape to insulate the poles and then threw it away. Plug in the new capacitor- re-hook the clip, reinstall the back panel, plug it in and verify that the fridge is working. Hook your water hose back up and move it back into place and you are done.