If you are having trouble opening your drawer easily or it has been damaged/broken, replacing the rear drawer glide could be the solution. The glide attaches to the rear of the oven drawer and supports the sides of the drawer. This allows the drawer to slide in and out of range without difficulty. Only one tool is needed for this repair, ...Read morea flat blade screw driver. Make sure to unplug the oven and wear gloves before repair to protect hands in case range is not cooled before repairing. This an OEM part sourced directly from the manufacturer.
This part is the replacement inner oven door glass for your oven. It is made of glass and is approximately 16 inches wide and 7 inches long. The oven door glass allows you to see inside the oven when the door is closed. The main reason to replace the inner oven door glass is if the old glass is cracked, broken, or missing. This part is an OEM part sourced directly from the manufacturer.
This steel washer is also known as the range washer and is used on your oven door. The measurements for the steel washer are a three quarter inch outer diameter, and a one quarter inch inner diameter. This washer is an OEM part, made of steel, which is sourced directly from the manufacturer. This specific steel washer is used with your ra...Read morenge, to secure the inner and outer door together and to secure the oven door handle back in place. Users have ranked this repair as a simple installation that should take you less than fifteen minutes to complete.
This is a bulb clip, also known as a sensor clip or bulb holder, which is designed to hold the thermostat bulb in place within the interior of various models of ovens. This clip is made of metal, measures approximately 1-inch in length and is a genuine OEM part, but is sold by itself and without the thermostat itself. The thermostat bulb,...Read more also known as a capillary thermostat, is used to measure the interior temperature of the oven during operation, and this clip secures it. If you notice your oven heats unevenly, too little or too much, this clip may be rusted, broken or damaged and causing the thermostat bulb to not detect the internal temperature properly. To replace this clip, you will likely need your user manual and a screwdriver and/or wrench. You will first need to disconnect your oven from the wall outlet and remove it from the wall. Use your user manual to locate the thermostat and use your screwdriver and/or wrench to remove the panel covering it. Here, you can likely replace the old clip with the new one, and then reassemble your oven.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
drawer was tilting and wouldn't slide open easily.
75 of 78 peoplefound this instruction helpful.
jennifer from La Habra, CA
Really Easy
Less than 15 mins
The old glides were broken off so I didn't know I needed these glides until I saw the parts section of the Manuel. When they arrived I snapped them in with no effort at all. P.S. The shipping is fantastic here......i ordered on Monday received them on Tuesday. Now that's shipping:>)
Was this helpful?
Thank you for voting!
Replacing Broken Parts
100 of 166 peoplefound this instruction helpful.
Scott from Noblesville, IN
Really Easy
Less than 15 mins
The two back door glides were missing and broken (one of each), and needed to be replaced. Finding the parts online was MUCH easier than I expected,and the repair was remarkably simple. Parts snapped into place, the drawer had to be lined up, and it slid right into place. Very easy!
Was this helpful?
Thank you for voting!
Internal glass broke on the oven door
41 of 43 peoplefound this instruction helpful.
EDWARD from PHOENIX, AZ
Easy
30 - 60 mins
Screw drivers
All the was needed was a Phillips screw driver. It's not difficult. Watch out because the door is spring loaded and does seperate quickly after all the screws are out. Be sure to watch the front panel, it appears to be heavy glass and can come out of the slots during the repair. I only had to re-assemble and dis-assemble 4 times before I
... Read moregot it right but it's still fairly easy to do if you take your time.