Quick Question!

Have you ever purchased from PartSelect.com before?

Models > REG75WL5

REG75WL5 Frigidaire Wall Oven - Overview

Get Parts and Repair Help for REG75WL5

If you know the wall oven repair part you need, you can browse the list of all parts on the REG75WL5, or you can search by name or part description. You can also find your part by where it is located on the REG75WL5 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your wall oven. We’ve also included any installation videos we have for REG75WL5 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the REG75WL5

[Viewing 3 of 3]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$34.18

Temperature Sensor

The oven temperature sensor for your range may also be called a probe. The quick connect on this part may differ than your original piece. If the temperature sensor does not fit yo...

$3.62

Main Terminal Block Kit

Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.

$23.65

Light Bulb Lens

The Frigidaire light bulb lens covers the interior light bulb in an oven. No tools are necessary to replace this item. After unplugging the appliance, slide off the wire bracket to...

$114.10

Bake Element

This is a 2100 watt bake element for your oven or range. The element supplies heat from the bottom of the oven to bake or cook your food. You may need to replace the bake element if your oven is not heating properly. Simply remove oven racks to access the bake element. Use a Phillips screwdriver to remove the two screws that secure the element to the oven body. Electrical wires feature slip-on connectors for easy installation, but be sure to hold the wires forward so the wires do not fall back through the rear of the oven. Unplug your appliance or shut off your circuit breaker to the appliance before installing the new part.

$9.73

LAMP

$35.45

Rack

$35.52

Light Lens Retainer Clip

This is a light lens retainer clip and it is used in conjunction with the oven on your range. This retainer clip secures the light lens to the oven cavity. The part is made entirel...

$161.00

Broil Element

This broil element supplies heat for cooking and is located in the roof of an oven. If there is little to no heat when cooking, a damaged element, or food is taking too long to cook, these symptoms could be solved by replacing this part. Before starting this replacement, make sure to unplug your range from the power source or shut off from the house circuit breaker. You will need a Phillips screwdriver to complete this repair. This part comes in a matte black color. For safety reasons, make sure to wear gloves. Refer to the manual provided by the manufacturer.

$136.98

SEAL

$46.23

RACK

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not heating to desired temperature

  • Customer: Dan from Bellevue, ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 110 of 166 people found this instruction helpful
Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with tw... read more

Cord was not tightened enough by delivery crew.

  • Customer: Timothy from Spring Valley, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 63 of 103 people found this instruction helpful
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screw... read more

Element showed a hot spot prior to failing open.

  • Customer: James from Delaware, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 24 of 26 people found this instruction helpful
Replaced element. Removed shelves, removed two screws and lifted/wiggles old element out to pull wires off at connectors. Reversed process installing new element and truned on to test/burn off "newness" Done! read more