Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JCTP70BM1BB

JCTP70BM1BB General Electric Wall Oven - Overview

Get Parts and Repair Help for JCTP70BM1BB

If you know the wall oven repair part you need, you can browse the list of all parts on the JCTP70BM1BB, or you can search by name or part description. You can also find your part by where it is located on the JCTP70BM1BB by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your wall oven. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the JCTP70BM1BB

[Viewing 5 of 5]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$18.39

Oven Light Housing

The light housing is also known as a lamp holder and is a part for the oven in your range. The function of this piece is to hold the bulb that will light up the inside of your oven...

$15.86

Oven Sensor

The function of the oven sensor is to detect the temperature within the oven cavity. If you notice that the oven is too hot or too cold, or it is not heating evenly, you may need to replace the oven sensor. The oven sensor is typically located in the back of the oven so you will most likely need to pull your oven out to access it. Many of our customers have rated this repair as easy. You will need a Phillips screwdriver to complete this repair. Be sure to disconnect the power source and shut off the gas valve before doing this repair.

$4.67

Oven Bulb Lens Cover - Glass

$2.12

Screw

This screw is sold individually.

$3.42

Screw

Sold Individually.

$3.60

Screw

Sold Individually.

$30.70

Door Gasket

This oven door gasket prevents heat from escaping the oven cavity when in use.

$45.90

RACK OVEN

$42.72

WINDOW PACK ASM

$3.60

SCREW

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven was not coming up to temperature

  • Customer: Sean from Highlands Ranch, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 36 of 41 people found this instruction helpful
I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wall. Overall, a very e... read more

Oven Lamp Holder Burned

  • Customer: Jack from Okmulgee, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 14 of 15 people found this instruction helpful
removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions. read more

Actual temperature did not match set temp

  • Customer: Brian from Fairfield, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
Removed the oven door for easy acces to oven. Unscrewed (philips screwdriver) the screw holding temp sensor in place. Gently pulled the wiring until quick connector was located. Pushed down on locking level on quick connect while holding other end of wiring (so wiring would not fall back behind oven). Connected the new sensor and screwed back in place. ... read more