Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JB570GM2

JB570GM2 General Electric Range - Overview

Get Parts and Repair Help for JB570GM2

If you know the range repair part you need, you can browse the list of all parts on the JB570GM2, or you can search by name or part description. You can also find your part by where it is located on the JB570GM2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for JB570GM2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the JB570GM2

[Viewing 4 of 4]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$37.57

Bake Element

At the floor of your electric oven is the bake element. This partially open-style element comes with push-on terminals. The bake element will likely provide most of the heat for ba...

$5.30

Single Heating Element Support Clip

The metallic clip, or also known as a broil element support, is for a oven element on a range. This part holds the broil element in place on top of the oven. If your support clip is broken then this replacement should be the solution. The tools needed for this project are slip joint pliers. For safety precautions, make sure to unplug your range from the power source, or shut off the house circuit breaker before starting this project. Refer to the installation instructions for best results and accuracy.

$27.95

Infinite Switch Kit

The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.

$108.02

Oven Sensor

It is possible that your oven is cold because of a fault in the temperature sensor. The temperature sensor regulates oven temperature in modern ranges, like a thermostat. It is on the back wall near the broiler on the top wall. On a newer oven, there may be a fault code displayed. Faulty temperature sensors are often responsible for F3 and F4 error messages on an electric range. Check your manual or the manufacturer website to find out the proper resistance of the temperature sensor. To check your sensor, unplug the oven and use a multi-meter to see if your sensor is at the correct resistance.

$33.20

Hinge with Roller - Right Side

This is a hinge with roller for the oven door on your range. The roller allows you to open and close the door with ease and control. If your door is not opening easily, you may nee...

$19.14

Broiler Pan - Large

This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain. The grate measures 15-1/2 inches wide by 13 inches deep and the pan is about 17 inches wide by 13 inches deep. No tools are required to replace this item, simply pull out the lower drawer of your range, pull down the front of the drawer, slide the pan out and slide the new one into place. This is a genuine part sourced right from the manufacturer.

$3.42

Screw

Sold Individually.

$40.48

Hinge with Roller - Left Side

This is known as a hinge with roller and it is for the oven door of your range. The hinge with roller allows you to easily open and close your oven door without much effort. Take note that your appliance requires two hinges, one located on each side of the door. We recommend changing both at the same time. This model is made for the left side of your unit, if you are looking to purchase one for the right side see the related parts section below.

$3.60

Screw

Sold Individually.

$53.31

Broil Element - 240V

This broil element is found on the roof of the oven and has push-on terminals.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bake element cracked on its own

  • Customer: Timothy from Cordova, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 595 of 600 people found this instruction helpful
Flipped the breaker. Removed shelf, Find the right size nut socket, unscrew the two screws, pull the element out a little bit, disconnect the wires (on pretty tight), pull out element, clean out any mess in the oven, compare element with new one to make sure its the same size and such, connect wires to new element, replace screws, flip breaker back, tur... read more

Oven took 30 minutes to get to 380 degrees-no hotter

  • Customer: Sandra from Hayward, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 379 of 382 people found this instruction helpful
First I searched this site and read about the repairs - which made me feel like my husband could do it with ease. Then he removed two screws inside the oven, removed the broken element (didn't know it was broken til removed) and replaced the new one - just like that! The real key was being able to read how it was for other people who had already done it. ... read more

Oven tempature was approximately 150 degrees to low

  • Customer: James from Austin, TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 200 of 228 people found this instruction helpful
This repair is EASY if you know how to use an ohm meter. If not, seek help for this step.

SYMPTOM:
The oven (JKP27WOP3WG or JKP27WP3WG and many ovens like it ) was not getting hot enough. Verifying the cooking temperature with an typical oven thermometer, I was able to determine that the oven was cooking temperature was about 150 degrees t... read more