This wheel is a dishwasher rack wheel designed for the upper rack of your appliance. The roller wheel is approximately 1.25 inches in diameters and includes the brushing you need for installation. It simply clips right on to the rack frame. After the wheel are attached to the side of the dishrack and are placed into the slides on either s...Read moreide of the appliance. Dishrack roller wheels allow the upper rack in a dishwasher to glide in and out of the appliance with ease. Due to the fact the roller wheel is made of plastic they tend to wear out after a period of time, also they can break. We do recommend you replace these rack wheels in pairs as they often wear out at the same rate. These wheels are sold individually.
This dishrack wheel is designed for use on the lower rack of your dishwasher, it allows the rack to roll in and out of your appliance with ease. This roller wheel includes the locking clip required for installation. The roller wheel attaches directly to the rack, you simply snap it into place on the frame of the rack, it does not include ...Read morethe axel. Due to how the roller wheels wear out we recommend replacing them in pairs. The diameter of the wheel is approximately one and a half inches. The roller wheel and clip are made of plastic.
This micro filter basket assembly is used in dishwashers. The filter is responsible for filtering the water inside the dishwasher. All of the food and debris particles that are removed from your dishes need somewhere to go, this filter works to remove that stuff from the water so the drain will not get clogged. Filters are supposed to be ...Read moreself-cleaning, however if you have hard water, or if you are using the wrong detergent they might get a build-up on them. You can clean these filters, but once they are worn out they will need to be replaced. This filter has a diameter of four inches, and it is five inches in length.
This dishwasher drain pump is a genuine OEM replacement part designed to efficiently remove water from the tub during the wash cycle. Compatible with a range of models from Bosch, Thermador, Gaggenau, and Kenmore, it plays a vital role in maintaining proper drainage and overall appliance performance. By channeling water from the tub to th...Read moree household drain, the pump ensures effective cleaning and prevents water retention. A faulty pump may result in poor drainage, reduced washing efficiency, water leaks, or unusual noise during operation. Replacing the pump restores optimal function and helps prevent potential damage or safety hazards. Sold individually.
This lower dishrack assembly is a genuine replacement part designed for select Bosch, Thermador, and Gaggenau dishwashers. Engineered for durability and optimal performance, it features a robust rack structure with integrated wheels for smooth gliding and a silverware basket for organized utensil placement. The silver finish complements m...Read moreost dishwasher interiors, while the sturdy materials ensure long-term reliability. Replacing a worn or damaged lower rack helps maintain efficient dishwashing, protects internal components from loose debris, and restores ease of loading and unloading. Compatibility should be verified using your dishwasher’s model number prior to installation.
This door seal, also known as a door gasket, is an authentic manufacturer replacement part for your dishwasher. It is responsible for creating a watertight seal between the tub and dishwasher door and preventing water from leaking out while the dishwasher is running. Therefore, if you notice water leaking from the front of your dishwasher...Read more and difficulties closing the door, then it is likely that the seal is either worn down, torn, or has a buildup of mold. Carefully pull the defective seal from the perimeter of the tub and clean the area thoroughly. Place the new seal in the grooves around the tub and close the dishwasher door to press it into place.
This dishwasher water inlet valve is a critical component responsible for regulating water flow into the appliance during the wash cycle. Engineered for precision, it opens and closes in response to signals from the control board, ensuring the correct amount of water enters the dishwasher. Constructed from durable materials, it helps main...Read moretain optimal performance and efficiency. Common signs of a failing valve include insufficient water fill, dry cycles, or water leakage. Installation typically involves disconnecting the water supply and electrical connections, and following the steps outlined in the owner's manual. Replacing a malfunctioning valve can restore proper function and prevent further damage to the appliance.
A holder is used in dishwashers, it is known as the dishrack stop kit. This kit comes with both the front and the rear stop, these parts are installed at either end of the rails that the upper rack slides on. These stops help keep the rack on the rail, without this part the upper rack of your dishwasher will not slide in and out of your d...Read moreishwasher properly. If you need to fix both the left and right rail you will need to order two kits. To install this part, you will need to remove the upper rack from your dishwasher, and you may need a flathead screwdriver. These front and rear rack stops are made of plastic and they are gray in color.
This drain hose is designed for use in dishwashers. After the wash cycle is complete the water need to leave the dishwasher, this drain hose it carries the dirty water from the drain pump to the kitchen sink drain. Because this part is made of plastic it can be damaged, which means you will need to check this part if you notice any leaks ...Read morecoming from your appliance. This hose is approximately five feet long, and it includes one o-ring. Before you begin repairing your dishwasher you need to unplug the appliance and shutoff the water supply.
This detergent and rinse aid dispenser is an important part in your dishwasher. It is located on the inside of the door and it holds and releases the detergent during the wash cycle of your dishwasher. The cover of the dispenser has a latch mechanism which is controlled by the electronic board or the timer. The latch releases to open and ...Read moredispense the detergent at the proper time during the cycle. Overtime the mechanism might wear out, or the latch might break. If your appliance will not dispense detergent you will need to check this part. Make sure the part it free of debris, and that the hinge can move freely. If there is nothing from preventing this latch from releasing and the dispenser door from opening, you may need to replace the dispenser.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The plastic clip on the roller broke
26 of 38 peoplefound this instruction helpful.
Catherine from AMHERST, NY
Very Easy
Less than 15 mins
We let this go for a shameful amount of time before I decided I could probably fix it. The roller broke so you could only pull it out about halfway or it would come off the track. I looked up the part, and bought it. Actually bought two in case it happened again. When I arrived I looked at how it was put together on the other side and t
... Read morehen just basically pushed it onto the rod and it was fixed. I am ashamed it took so long to do it. Never be afraid to try it yourself. It was a total of $10 shipped to fix it.
Read less
Was this helpful?
Thank you for voting!
My dishwasher was not draining
21 of 34 peoplefound this instruction helpful.
Karen from CRESTON, IA
Easy
15 - 30 mins
Screw drivers
With the help of You Tube, this 50 year old Mom got the job done. Not that complicated if you watch the step by step instructions on the Appliance Pro video. My repairman and husband were both determined to just buy a new one but this 20 year old dishwashing genius was just in need of a little repair. Only need a screwdriver, and sli
... Read moreghtly confusing as wires hook on a little different on new pumps. I suggest watching video the whole way through and then playing it step by step as you do the repair. Worked great for me. Thanks.
Read less
Was this helpful?
Thank you for voting!
Spring assembly on detergent and rinse aid dispenser broke so the sliding lid would not operate
18 of 28 peoplefound this instruction helpful.
Steven from SUWANEE, GA
A Bit Difficult
30 - 60 mins
Screw drivers
Here are the steps you need to take to do the job properly:
1. turn off electrical circuit breaker to the dishwasher 2. remove 8 total hex screws (3 on each side and 2 at the top) of the inside door panel. The door panel will slide off so be careful and it happens pretty quickly when the last hex screw is removed. 3
... Read more. unplug the wiring harness to the detergent/rinse aid dispenser 4. you need to use a flat head screw driver to lift the metal flanges on the top and bottom of the detergent/rinse aid dispenser. 5. the unit will pop out toward the inside of the dishwasher 6. insert the new detergent rinse/aid dispenser and very important all metal flanges are pulled back over the plastic edge (top and bottom) of the dispenser unit. The screw driver needs to be used to assist in pushing the dispenser unit as tight to the frame of the door to ensure the metal flanges grab hold and lock in. 7. re-attach the wiring harness 8. re-install the dishwasher door with 8 hex screws. Doing this step alone is challenging as the door frame will want to keep going up to close. I used a small foot stool and placed it inside the dishwasher front area on top of the inside metal door area so the door would stay open roughly half way. I then used my knees to prop up the outer door cover while i got 2 screws started then was able to easily complete the job. 9. run the dishwasher with a detergent packet loaded into your new dispenser. I checked for 15-20 minutes during initially running to insure no issues or leaks. 10. One last note - my Bosch dishwasher had a custom wood door installed to the outer panel to blend in with our kitchen cabinets. The door itself was much heavier as a result. Some of you may not experience the slight difficulty i noted above in step 8. Good luck.