FL25C (Type 2) Weed Eater Trimmer - Overview

This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filt...Read moreer is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.

This genuine fuel tank assembly is an original replacement part sourced directly from the manufacturer and is commonly used in Craftsman trimmers and weedwackers. Made from high-quality plastic for durability, it includes the attached fuel tank cap for a secure seal. Replacing this part may require an Allen wrench or hex key, depending on...Read more your model. The fuel tank assembly is sold individually and is designed to meet OEM standards for fit and performance.

This Fuel Line is a 25-inch, clear, plastic line used to deliver fuel. It requires a screwdriver, pliers, socket set, and nut driver and is rated as "Easy" to install by customers. If the fuel line wear out to the point of breaking, cracks and/or leaking will appear and the part should be replaced. Refer to your make, model and diagram to ensure this is the correct part for you.

The Fuel Cap with retainer, often simply known just as the fuel cap, keeps fuel from splashing out of your tank and debris from entering it. Black in color, it is sold individually and made of plastic. Because of everyday fatigue and wear, the cap can become damaged over time and must be replaced. You will know if it is time to replace ...Read moreyour fuel cap if you notice visible damage or experience fuel leaking from it. You can make this repair by hand, just attach the cap directly back onto the fuel tank. Most of our customers found this repair very easy.

This purge bulb is an authentic OEM part from Craftsman for gas blowers, trimmers, blowers and weed wackers. This part disperses fuel to the carburetor to provide starting the blower faster. You will need a screw driver to replace this part. This purge bulb is made of rubber and sold individually.

Genuine Weed Eater replacement part, this item is sold individually. The 530058000 Trigger is inside the handle of the trimmers shown below. It connects to the throttle cable which controls the speed of the spool assembly on the Trimmer.

This flywheel is an authentic manufacturer replacement part for use with lawn and outdoor equipment. The flywheel is a heavy, circular disc that has magnets that create an electric charge sent to the spark plug to create the spark that ignites the fuel and air mixture in the engine. It is attached to the engine crankshaft by a key known a...Read mores a shear pin or flywheel key. This assembly is a critical component in the starting and running of your power equipment. Over time, the magnets on the flywheel will wear down, and the flywheel may chip and crack. A faulty flywheel will result in a loss of power, excessive shaking during use, and difficulty starting the equipment. Remove the flywheel using a flywheel puller. Position the new flywheel on the crankshaft and secure it with the retaining nut and flywheel key. This flywheel is sold as an individual replacement part.

This is an Original Manufacturer Approved replacement part. This part is made out of Foam and it is sold individually. The purpose of the filter is to keep dust and debris from contaminating the carburetor and engine. Once an Air filter becomes dirty, it constricts the flow of air to the engine so it will not run properly. Air Box and Air Box Cover are sold separately.

The Starter Spring is a metal spring used to restract the rope after you pull it to start the engine. Installation of this OEM part is rated as "Medium" difficulty and requires a screwdriver, nutdriver, and torx bit. The part is installed inside the recoil housing. If broken, the rope will not retract and the part must be replaced.

This metal ring in your engine, known as the piston ring, seals the gap between the piston and cylinder wall. It makes sure that the gases produced during combustion do not escape and that the engine maintains the pressure it needs to run. If the piston ring is damaged, oil can seep into the combustion chamber, causing your engine to exhi...Read morebit rough idling and your machine emit blue smoke. To switch out a defective piston ring, detach the old ring from the piston with a screwdriver. When installing the new ring, you may need to compress it to make it fit properly. Please be aware that this genuine OEM replacement part is bought individually. It is recommended that you replace all the piston rings in your machine at once, as they tend to wear down at the same rate. Carefully review your user manual to determine how many rings your machine needs before placing your order.

This ignition module is a genuine OEM sourced item, it is not an aftermarket imitation. Ignition module supplies electric current to the spark plug. If the ignition coil is defective, the engine may not start. Please note, this assembly includes a metal ignition module with a rubberized wire and the spark plug boot. To complete this repair you will need a screwdriver.

This is a standard hardware which has multiple applications based on your tool. It is sourced from original equipment manufacturer for use with a variety of power equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. Requires a hex key or an allen wrench to install or remove it.