Quick Question!

Have you ever purchased from PartSelect.com before?

Models > F45WJ26HW1

F45WJ26HW1 Frigidaire Refrigerator - Overview

Get Parts and Repair Help for F45WJ26HW1

If you know the refrigerator repair part you need, you can browse the list of all parts on the F45WJ26HW1, or you can search by name or part description. You can also find your part by where it is located on the F45WJ26HW1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for F45WJ26HW1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for F45WJ26HW1

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$13.80

Defrost Timer - 60Hz 120V

Defrost timers are part of the defrost circuit in your refrigerator and freezer. This timer cycles the defrost heater on and off. For every eight hours, the appliance timer will cy...

$100.41

Ice Maker with Cover - 8 Cube

This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice is automatically ejected and the process continues until the storage bucket is full. Your ice maker should be replaced if ice is not being generated, stored, dispensed, or the ice maker has been damaged. Replacing the ice maker is an easy job and only requires a 1/4 inch nut driver. Before you start this repair, make sure your refrigerator is unplugged. For help with this installation, check out the video below.

$26.97

Door Handle

The screws and trims are NOT included with this handle.

$103.77

Replacement Ice Maker

This replacement icemaker may also be known as the ice maker assembly and is compatible with your refrigerator/freezer. This assembly replaces the heat-release ice maker unit only. The kit comes with four round female connectors at the end of the wire harness. It also comes with the adaptor that converts the harness to three round female, and one round male connectors. The tools you will need in order to make this installation include a 1/4-inch nut driver, and a Phillips screwdriver. Before starting this repair make sure to unplug your refrigerator and shut off the water supply.

$141.87

Ice Container and Auger Assembly

This assembly includes the auger and blades.

$31.27

Dispenser Crusher Housing

This dispenser crusher housing may also be known as a refrigerator ice crusher housing, and is compatible with your refrigerator. The function of the dispenser crusher housing is to shield the ice crushing blades within the ice container. To make this repair you will need a Phillips screwdriver, a flat blade screwdriver, a quarter-inch nut driver, and a pair of channel lock pliers. For this installation, work gloves are recommended. Note that this piece may look different or be a different color than the original, but this part will fit and function in the same way as the original part.

$15.70

Defrost Thermostat

This limiter thermostat cuts out when the temperature inside your refrigerator reaches 55 degrees Fahrenheit and kicks back in when the internal temperature drops to 20 degrees Fah...

$5.94

Crisper Drawer Cover Support

$38.22

Ice Container/Bucket

Bucket only. All other parts sold separately.

$7.95

Drum

This part helps push the ice through the front plate to be crushed.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Fridge got warm and freezer coils were frosted

  • Customer: Stephen from Warrington, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 303 of 357 people found this instruction helpful
Fridge is a side by side. The freezer is pretty narrow for a guy with wide shoulders.

Pulled plug.

Had to remove bottom drawers then used nut driver to remove screws closest to back wall in drawer runners. Once the back screws were removed the runners could be swung up or down out of way so back cover could be removed.

On... read more

Broken ice maker

  • Customer: Juan from Miami, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 178 of 236 people found this instruction helpful
Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice. read more

Ice Maker Stopped Working

  • Customer: JACK from MESA, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 134 of 146 people found this instruction helpful
It was pretty straight forward. Remove the two screws that hold the unit to the wall of the freezer. In my case, I had to use a different ice maker than what came with the frig. In order to install the replacement unit they sent a wire adaptor so it would attach to the existing wiring. That too was all fine and dandy. The only problem was that the ... read more