This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
If you notice an unusual noise coming from your freezer, the evaporator fan blade might be the problem. Frost-free freezer models use evaporator fans to move air through the evaporator for more efficient cooling. If the evaporator fan blade gets damaged or worn it may become noisy. If the blade is loose on the motor shaft or if the fins a...Read morere damaged, it should be replaced. Be sure to remove power to the appliance before attempting any repair. The evaporator fan assembly is located behind the air grille or evaporator cover and can normally be accessed by simply removing a few mounting screws. The fan blade is normally pressed on to the motor shaft and secured by a spring clip.
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a pr...Read moreotective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.
This metal freezer door key has a cross shape and is approximately 2 inches long. If your freezer door will not stay shut, you can use the key as a quick fix to keep it closed. If your key will not lock, or unlock the freezer door, check to see if it has been bent or damaged. If the key is damaged, you should look to replace it to avoid d...Read moreamaging the lock. The key should engage the locking mechanism with ease. If the lock sticks when you turn the key, penetrating fluid should be used to loosen the mechanism. These keys are sold separately, and should be stored somewhere safe and not next to the unit.
This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Connie - For model number EVL201NXRQ05
May 7, 2026
Lower shelves are below freezing. Upper 2 shelves are above freezing. What do I do?
I should have added that my freezer is now empty because I relocated all contents. Nothing is blocking airflow. Upper is above, lower is below freezing. What could it be? Thanks
Hi Connie, thank you for the question. Based on our understanding, the issue could be with the evaporator fan motor, part number PS11740626. It is responsible for pulling air across the cooling coils and pushing it throughout the freezer. If it has failed, cold air won't reach the upper shelves. You may need to replace it to fix the issue. We hope this sorts out your problem!
What keeps my freezer from not getting colder then 20 degrees?
Hi Edward,
Thank you for your question. If the freezer is too warm, then the thermostat is likely malfunctioning. The thermostat is a rotary dial with a capillary tube and sensor bulb which monitors the temperature, and electrical contacts which power the compressor circuit. Overtime, these parts can become worn preventing the thermostat from working correctly. Try adjusting the thermostat to the highest setting. If the compressor starts then the temperature control should be replaced. Make sure not to disturb the sensor bulb when checking these components. We hope this helps!
I have to defrost the freezer about every three weeks. After defrost, I run wire up and down drain, use hot water and baking soda to ensure drain is clear. Actually poured enough water through drain to get a inch or so in pan, then emptied. Thought the igloo temp setting might be causing it, so lowered to 5. The drain freezes up again in a 2-3 weeks. Any suggestions?
Hi James. It could be a bad defrost timer. Thank you for your question and good luck with your repair.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lights inside refrigerator not working
137 of 257 peoplefound this instruction helpful.
Clint from Rayville, MO
Really Easy
Less than 15 mins
Screw drivers
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.
Was this helpful?
Thank you for voting!
Froze over fan motor burnt out
73 of 82 peoplefound this instruction helpful.
James L. from Madison, AL
Easy
15 - 30 mins
Nutdriver, Screw drivers
Removed shelves from inside freezer then removed 4 screws holding cover panel. Pulled panel up and slightly pulled forward to remove. Removed wiring connections then removed two screws that held the motor & fan assembly. Removed the support bracket from the old motor and installed same on the support bracket. Reversed removal procedur
... Read morees for installation. Cover panel is a little bit of a problem when trying to reinstall. Put in panel as high as you can and then slide down. You must then exert a little pressure on the bottom portion to get it to seat correctly. Install four remaing screws and you are done. I had this repaired previously by a professional repairman and noticed from the pictures you folks provided that he had installed the screws on the support bracket incorrectly. That was the reason for the fan blade to rip apart.
An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only
... Read moreswing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.
My Orders
