This manufacturer-approved air filter system for refrigerators eliminates odors and any impurities. It does this by neutralizing and removing odor-causing molecules. For best results, it is important to change the filter every 6 months to ensure that food is kept fresh, and the humidity is controlled. This part measures about 7 inches wid...Read moree and 5 inches deep. Follow installation instructions provided by the manufacturer when installing this part to ensure accurate results and further guidance. Remember to unplug the refrigerator from the power source before starting this project. The air filter may be located in different places depending on your appliance, but is usually on the inner right or left side. See your manual for exact location. Our customers rated this as a very easy repair that takes only a few minutes; just locate and remove the old air filter and insert the new one to complete the repair, which requires no tools.
This evaporator fan motor is 115V. If you notice that your freezer is noisy or is too warm, you may need to replace the evaporator fan motor. This package comes with the evaporator fan motor itself, as well as a wire harness. The evaporator fan motor is in the back of the freezer, so you will need to remove your freezer shelves and the ba...Read moreck panel before you can access it. The function of the evaporator fan motor is to circulate air over the coils. The coils convert the heat into cool air, which is then circulated. Be sure to remove the power source from the freezer before you begin this repair.
Sold individually.
This is a genuine part. The handle mounting shoulder screw (no.10 ab) is made for use with many refrigerators. The metal screw helps to fasten the handle assembly to the outer door panel. The handle mounting shoulder screw is sold individually. For the repair, you will need a pair of pliers.
This part could be found underneath a fridge, dryer, or freezer. The original foot may be cracked, broken, or perhaps missing altogether. If you notice the appliance is uneven to the floor or wobbling, it may indicate that the levelling foot needs to be replaced. You will need pliers and a block of wood to perform this task. There will be...Read more one adjustable foot found in the package. Lift the dryer and place the wood to keep it propped up. You may need to use the pliers to remove the old foot. Screw the new foot into place using your hand. Once the new leveling foot is in place, lift the appliance and remove the block. Test the machine out to ensure it is now sitting level.
This is a door gasket for the freezer compartment of various refrigerators. Door gaskets are used to seal the cold interior of the freezer compartment, from the warm and ambient temperature of your home. If this door gasket on your freezer door is damaged, moldy, or warped and unable to close and seal properly, it needs to be replaced imm...Read moreediately. This door gasket is gray in color and is easy to remove and install. To replace it, carefully pull and remove the old gasket off, and wrap the new gasket around the perimeter of the door frame. This gasket is sold individually, and does not come with any accessories.
This genuine OEM hinge mounting screw is designed for use in Frigidaire and Electrolux refrigerators, providing a secure and reliable way to fasten door hinges to the cabinet. Built with a durable hex washer head and standard threading, it helps restore proper door alignment and maintain a tight seal to prevent cold air loss. Ideal for re...Read moreplacing worn, stripped, or corroded hardware, this heavy-duty screw ensures long-lasting stability and dependable everyday performance.
This run capacitor supports the compressor by storing and releasing electrical energy for smooth startup and operation. It helps maintain consistent cooling performance and efficiency. Replacing a faulty capacitor can resolve issues like clicking sounds, failure to start, or reduced cooling.
This stainless steel defrost heater is designed to melt frost buildup from the evaporator coils during the automatic defrost cycle, ensuring consistent airflow and temperature regulation within the refrigerator and freezer compartments. Positioned near the evaporator, it activates periodically to prevent ice accumulation that can obstruct...Read more cooling performance. A properly functioning defrost heater supports energy efficiency, reduces compressor strain, and helps maintain food freshness. Common symptoms of a failing heater include excessive frost, temperature fluctuations, and prolonged appliance run times. Replacing this component restores optimal cooling and system balance.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer thawing at about 20 degrees
21 of 27 peoplefound this instruction helpful.
Nathan M. from Bunnell, FL
Easy
15 - 30 mins
Screw drivers
Turned freezer off at themostat and unplugged freezer. Removed 2 screws at front 2 at the back and 2 at the top. Lowered top cover and removed evaporator fan bracket (2 more screws) removed themostat capulary tube( 1 screw and bracket) then unplug fan motor. Removed motor from bracket (2 screws). Put on new fan motor then removed fan b
... Read morelade from old motor and put on the new motor. Remounted fan motor bracket and thermostat capulary tube. Remounted top cover, plugged freezer in the set the thermostat to 4 and freezer is working fine and doing its job. I orderedmotor on a Sunday and it was shipped on Monday and I received said part at 7:pm on Wednesday.
Read less
Was this helpful?
Thank you for voting!
you r label (this end in arrow is wrong
15 of 25 peoplefound this instruction helpful.
melvin from BASKING RIDGE, NJ
Really Easy
Less than 15 mins
placed filter in sideways
Was this helpful?
Thank you for voting!
Evap fan motor intermitant
11 of 17 peoplefound this instruction helpful.
Mike from Los Banos, CA
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
Removed evap cover from Commercial Refrigerator. Removed mounting screws from Evap motor mount. Replaced evap fan motor. Repositioned. Reinstalled evap cover. Tested . This motor was hard to find locally. Glad I called.