Quick Question!

Have you ever purchased from PartSelect.com before?

Models > E30EW7CEPS1

E30EW7CEPS1 Electrolux Wall Oven - Overview

Get Parts and Repair Help for E30EW7CEPS1

If you know the wall oven repair part you need, you can browse the list of all parts on the E30EW7CEPS1, or you can search by name or part description. You can also find your part by where it is located on the E30EW7CEPS1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your wall oven. We’ve also included any installation videos we have for E30EW7CEPS1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the E30EW7CEPS1

[Viewing 5 of 5]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$34.18

Temperature Sensor

The oven temperature sensor for your range may also be called a probe. The quick connect on this part may differ than your original piece. If the temperature sensor does not fit yo...

$3.62

Main Terminal Block Kit

Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.

$125.16

Bake Element - 3400W

This bake element is found on the bottom of the oven.

$5.35

Steel Washer

This steel washer is also known as the range washer and is used on your oven door. The measurements for the steel washer are a three quarter inch outer diameter, and a one quarter inch inner diameter. This washer is an OEM part, made of steel, which is sourced directly from the manufacturer. This specific steel washer is used with your range, to secure the inner and outer door together and to secure the oven door handle back in place. Users have ranked this repair as a simple installation that should take you less than fifteen minutes to complete.

$6.73

SCREW

$11.59

FAN BLADE

$9.12

NUT

$28.24

RACK

$13.10

SUPPORT

$5.63

TOOL

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not heating to desired temperature

  • Customer: Dan from Bellevue, ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 110 of 166 people found this instruction helpful
Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with tw... read more

Cord was not tightened enough by delivery crew.

  • Customer: Timothy from Spring Valley, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 63 of 103 people found this instruction helpful
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screw... read more

Element burned up.

  • Customer: Lynn from Denton, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 38 of 57 people found this instruction helpful
Removed old element and plugged in new. Very simple. read more