CGS700P4M4W2 General Electric Range - Overview

This burner grate foot, also known as a bumper, is an authentic OEM replacement part for your range. It is a small black rubber component that acts as a buffer between the metal grate and the surface of the cooktops to prevent scratches and damage to the cooktop. It also stabilizes the burner grate and prevents it from shifting or sliding...Read more, which reduces the risk of accidents or spills. These small components can easily fall and become lost while cleaning or wear down over time. Inspect each of the feet and ensure that you order the correct amount for your range. Each burner grate foot is sold separately.

This burner cap is for your gas range, and acts as a cover for the burner head. It is black in color and just over 3 inches in diameter. If your old burner cap is damaged or missing, this is the part that will replace it. This is an OEM part sourced directly from the manufacturer and is sold individually.

This is a replacement burner cap for your gas range or cooktop. The burner cap is found on the burner head, and prevents debris from getting into the head when it is not in use. The cap is black in color and is sold individually. It is a little more than 4 inches in diameter. To replace the burner cap, simply remove the damaged cap, and r...Read moreeplace it with the new one. No tools are required for this repair. This is an OEM part from the manufacturer.

This is a burner cap for your gas range. The cap acts as a cover for the burner head. If your old burner cap is damaged or missing, this is the part that will replace it. The cap is black in color and about 3 and a half inches in diameter. This is a quality OEM part sourced directly from the manufacturer. This cap is sold individually.

This is a door handle fastener to secure the handle to your refrigerator drawer. It is also known and a mounting bolt or screw. It is approximately 1 inch in total length, and is made of metal.

The light housing is also known as a lamp holder and is a part for the oven in your range. The function of this piece is to hold the bulb that will light up the inside of your oven. As per the manufacturer instructions, if your bulb has burnt out you must buy the bulb for this part locally. This light housing is roughly five inches high, ...Read morewith an outside diameter of roughly four inches by four inches. To install this part, you will need a Phillips screwdriver, a nut driver, and a pair of pliers.

This probe is used to check the internal temperature of the meat to ensure proper temperature is reached. Also known as a Meat Probe.

Proper burner performance depends on a cap that matches the burner head and lies completely flat. Cracks, damaged mounting feet, or heavy buildup can cause poor ignition and an uneven flame. Inspect the burner head, ports, and igniter before ordering a replacement. Match the caps size, shape, and color to the full appliance model and burn...Read moreer location. Allow every surface to cool before lifting the old cap, do not force the replacement into place, and confirm that the flame burns evenly after installation.

Irregular flames or poor ignition can result from damage or buildup in the surface burner base. The base supports the burner cap, routes gas to the flame ports, and helps keep the flame pattern balanced. First remove loose debris, make sure the cap sits flat, and check the igniter for cracks or misalignment. Match the replacement to the r...Read moreanges full model number, burner size, and position. Shut off both gas and electrical power before removal. Reassemble without bending the igniter or changing any gas components, then verify that the flame is even and mostly blue.

This part is a replacement screw for your oven. It is made of black metal and is sold individually. This screw is approximately 1/4 inch in diameter and about 1/2 inch in length. It is designed to connect the different parts of your oven door. This part is an authentic OEM part sourced directly from the manufacturer.

This is an official gas igniter for various models of oven. This part is used to ignite the burner within models of gas GE ovens. If your oven is experiencing heating issues, this igniter has likely failed or will fail imminently, and will need to be replaced. Replacing this igniter will require a screwdriver, pliers, and a wrench. This igniter is sold as an individual OEM part and does not come with any other parts.