Models > CA13DJD

CA13DJD General Electric Freezer - Overview

Sections of the CA13DJD

[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Shoulder Screw – Part Number: WR01X10623
Shoulder Screw
★★★★★
★★★★★
(2)
PartSelect #: PS1483099
Manufacturer #: WR01X10623
This is a self-tapping sheet metal screw and is used in conjunction with multiple appliances in your household. This part is size eight and has 18 threads to the inch. The AB in the name indicates tha...
$14.72
  In Stock
Water Tubing Clip – Part Number: WR1X5278
Water Tubing Clip
PartSelect #: PS295031
Manufacturer #: WR1X5278
$6.68
  In Stock
Door Shelf Retainer Bar End Cap Kit – Part Number: WR2X9486
Door Shelf Retainer Bar End Cap Kit
PartSelect #: PS299868
Manufacturer #: WR2X9486
This is a door shelf retainer bar end cap kit for a refrigerator. This kit contains two end caps that are made entirely of plastic and are white in color. They are each under 2 inches tall. This part ...   No Longer Available
Screw – Part Number: WR1X1249D
Screw
PartSelect #: PS294429
Manufacturer #: WR1X1249D
Comes 12 in a pack.   No Longer Available
Power Cord – Part Number: WR23X10300
Power Cord
★★★★★
★★★★★
(2)
PartSelect #: PS759476
Manufacturer #: WR23X10300
This heavy-duty cord has a three-pronged plug (2 electrical, 1 grounding). The power cord supplies power to your refrigerator, allowing it to keep the contents inside cool. There could be an issue wit...
$24.13
  In Stock
SWITCH LIGHT/LAMP PLUN – Part Number: WR23X10632
SWITCH LIGHT/LAMP PLUN
PartSelect #: PS2344359
Manufacturer #: WR23X10632
$28.90
  Special Order
Drain Plug – Part Number: WR02X10073
Drain Plug
PartSelect #: PS284532
Manufacturer #: WR02X10073
$24.39
  Special Order
Tubular Fastener – Part Number: WR2X4990
Tubular Fastener
PartSelect #: PS298031
Manufacturer #: WR2X4990
$10.23
  In Stock
R134 DRIER – Part Number: WR86X25269
R134 DRIER
PartSelect #: PS12727537
Manufacturer #: WR86X25269
The filter dryer filters refrigerant that travels through the sealed system of the refrigerator.
$56.83
  In Stock
SUPPORT – Part Number: WR2X7621
SUPPORT
PartSelect #: PS298561
Manufacturer #: WR2X7621
  No Longer Available
SHELF SUPT – Part Number: WR2X6250
SHELF SUPT
PartSelect #: PS298196
Manufacturer #: WR2X6250
  No Longer Available
LEVELNG JACK – Part Number: WR2X5676
LEVELNG JACK
PartSelect #: PS298100
Manufacturer #: WR2X5676
$8.61
  In Stock

Questions And Answers for CA13DJD

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the CA13DJD

[Viewing 2 of 2]
Leaking
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Two of the two leveling jacks of this old refrigerator were missing and had to be replaced.
I ordered four leveling jacks from this site for the refrigerator using a slightly different model number (my model was not listed). I assumed that the jacks all had the same shaft diameter and thread size. However, it turned out that the two front jacks had half-inch shaft diameters. It could be that originally there were rollers in front. The two rear jacks had quarter-inch shafts with "feet" for supporting them on the floor. So, I had to return the four jacks I had ordered and find another solution. I found two half-inch threaded bolts at the local hardware store that fit the front holes perfectly. I purchased 3.5 inch bolts to give me enough room to find the proper adjustment. I used wooden blocks and a crow bar to raise one side of the refrigerator high enough to screw in the leveling jacks. I used an adjustable crescent wrench to turn the bolts' hex heads until they were the proper height. I used the two original quarter-inch jacks in the rear holes and adjusted them to the proper height to level the refrigerator on the concrete floor where it is located. Then I removed the wooden blocks and tested to make sure the refrigerator did not wobble. I found that using the two bolts (no leveling jacks for the front holes could be found) for the front jacks proved to be the ideal solution. The job took me about thirty minutes, including the time it took to move the refrigerator into its final location and adjust the leveling jacks once more to create a solid stance so that the refrigerator did not wobble. While I had the refrigerator away from the wall, I removed the rear panel and cleaned the blades of the cooler fan and removed dust and dirt build up near the compressor with a vacuum cleaner. Then, I screwed the panel back into position, moved the refrigerator into its final place in a corner of the garage and made sure there was enough air space around it to allow for proper air circulation. This took me about twenty more minutes. I plugged it back in and listened to it come alive again. It is old but has never needed a repair and keeps everything cooled or frozen. I would suggest using threaded hex-head bolts in place of original leveling jacks if they cannot be obtained. Problem solved.
Parts Used:
LEVELNG JACK
  • Bruce K from RESTON, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!