This is a center crisper rail for your refrigerator. This part acts as a support rail for the crisper drawer by holding the center of the crisper frame. You will need to replace this part is if your current drawer is not opening or closing properly. This crisper rail is white and it is made entirely of plastic. It is roughly 13.5 inches long, and 2.5 inches wide. This is an easy repair which requires no tools.
This light switch may also be known as a refrigerator door switch or a light switch kit, and is compatible with your refrigerator. The function of the refrigerator door switch is to turn on the light when your fridge door is open, and to make sure it is off when your refrigerator door is closed. The reason you would need to replace this p...Read moreart is if your light is not turning on when your door is open. For this repair, you will need a putty knife, and a small flat-blade screwdriver.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
The p-trap drain tube kit may also be known as the duck bill, or the drain pipe, and it is compatible with your refrigerator. The function of the p-trap drain kit is to carry the water that has formed during the defrost cycle to the bottom of the refrigerator, where your drain pan is located. The tools you will need for this repair includ...Read moree a 1/4-inch nut driver and a small flat-blade screwdriver. To do this repair you will need to pull the refrigerator forward in order to reach the lower access panel at the back. This kit includes the tube extension piece and spacer.
Sold individually. Crisper drawer is an original equipment manufacturer (OEM) part that fits some bottom-freezer Kenmore, Amana, Crosley, Jenn-Air, KitchenAid, Maytag and Whirlpool refrigerators.
The crisper drawer is approximately 6-7/8-inches tall, 14-inches wide and 15-inches deep.
The electronic control board is used in refrigerators to monitor and manage the temperature settings, such as cooling or defrosting times. If your fridge or freezer is too warm, too cold, is not defrosting, will not start, and/or runs too long then replacing the control board could solve your appliance problem. The tools needed for this i...Read morenstallation project is a small flat blade screwdriver. *Please note: the board will need to be programmed after installation. Remember to unplug refrigerator from power source as a safety precaution. Refer to the manual provided by the manufacturer for further installation instructions and accurate guidance.
This refrigerator shelf frame is designed to support the glass shelf positioned above the crisper or pantry drawer, helping to keep your fresh food items organized and easily accessible. Crafted for durability and a precise fit, it is compatible with a range of refrigerator models. Please note that this listing includes the frame only; th...Read moree glass shelf and center support are not included and must be purchased separately. Installation is straightforward—simply remove the old frame and slide the new one into place to restore the functionality of your refrigerator’s storage space.
This is a deli drawer glide for the right side of your refrigerator. It allows the deli drawer to glide in and out smoothly. In order to access your glider, you will have to remove drawer and shelf, and unscrew the existing screws. Reverse and reinstall. This part is approximately 14.5 inches long, and made of white plastic.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
This is a replacement pan glide for your refrigerator. The pan glide can be found attached to the refrigerator shelf, and allows the pan to slide in and out efficiently. If your refrigerator pan will not slide in or out of place properly, or if the pan will not stay in place, you may need to replace the glide. There is a pan glide on the ...Read moreleft and the right side of the refrigerator shelf. This part is the left side glide, so be sure to determine whether you need to replace the left glide or the right glide. This part is made of white plastic, and is approximately 15 inches long.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John - For model number ABB2224BRW00
February 7, 2023
Fan is working, freezer is ice cold, but inside fridge is warm. Turning up cold setting does not keep milk/juice any colder. Coils cleaned yesterday. Any ideas on what part(s) may need replacement?
Hello John, thank you for reaching out to us. We would recommend checking the damper control assembly, part number PS11750106. The damper controls the cold airflow from the freezer compartment into the refrigerator compartment. Thank you for your inquiry, good luck with this repair.
can I clean the drip pan? I have an odor and I have cleaned all the inside and the bottom freezer
Hello Carol, Thank you for your inquiry. Yes, you can clean the drip pan. You first need to turn off the power and water supply to the refrigerator. The pan has or may still have two pieces of tape that hold it in place and to remove the first one, you need to access the back of the refrigerator, remove the panel with a nut driver, then disconnect the water inlet valve (using a towel to catch any drips) by pressing on the tube releases with a flat wrench. Then use a knife to cut the first strip of tape. Now go around to the front of the refrigerator, and remove the kick plate by pressing the locking tabs on each side. Use a nut driver to remove the water filter housing, and you should now be able to access the other end of the drip pan to remove the tape and pull it out to clean it. We have included a link to our video for a similar part to give you an idea of how to access it. We hope this helps you.
What should the freezer and refrigerator settings be. One guy I asked said Freezer on 5 and refrig on 3. Another guy said 4 and 4. So what is the
correct settings.
Thanks,
Hi Richard, thank you for contacting us. We have found that the recommended temperature setting for the refrigerator and freezer for your model are 4 and 4. We hope this information helps!
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Adrian - For model number ABB2224BRW00
December 26, 2019
The lights do not come on inside the refrigerator when the door is opened. I have replaced both bulbs, but that made no difference. Any suggestions on what else to check?
Hi Adrian,
Thank you for your question. If you have just replaced the light bulbs and the lights are still not coming on inside the refrigerator when you open the door, you will need to check both the door switch and the light socket with a multi-meter to see which part is causing the issue. We hope this helps. Thank you and have a great day!
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Spencer - For model number ABB2224BRW00
January 5, 2022
Does this model have a water filter for the ice maker? We recently noticed that it has stopped producing as much ice as it use to and I dont know why.
Hello Spencer, thank you for writing. There is not a water filter for this model. You may need to replace the water filter. Good luck and have a great day.
Was this helpful?
Thank you for voting!
Prev
1
2
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer is cold, Refridgerator is not as cold as it should be
384 of 472 peoplefound this instruction helpful.
Russell from Hardinsburg, KY
A Bit Difficult
More than 2 hours
Screw drivers
Having seen this problem before in other equipment so I had an idea where to look. Problem: the automatic defrost function was not operating. Looking through openings in the back panel of the freezer compartment, you could see the evaporator coils and fins were a solid chuck of ice. There are three logical components to check. Heater
... Read moreelement, thermostat (located just above the evaporator) and a relay on the control board (located in the fridge control panel). Checked the heater with an ohm meter -- OK. The thermostat closes the circuit at around 20 degrees and opens at around 32 degrees. Pulled out the thermostat, wiring, fan unit. Everything unplugs, unscrews, and unclips, don't cut wires. Put the whole assembly in a friends freezer for an hour or so to see if the thermostat closes -- OK. Problem had to be with the control board. Replaced control board, reprogrammed it per included instruction. Everything is working again.
Read less
Was this helpful?
Thank you for voting!
Cracked & Snapped Center Crisper Rail
230 of 256 peoplefound this instruction helpful.
Ruth from Roxbury, MA
Really Easy
Less than 15 mins
A very easy fix took all of five minutes
Was this helpful?
Thank you for voting!
defroster mode was not working causing freezer to ice up and refrigerator to be warm. Also fan was running continuely
189 of 228 peoplefound this instruction helpful.
James from Welches, OR
A Bit Difficult
1- 2 hours
Nutdriver, Screw drivers
The hard part for me was figuring out which part was causing the problem. I read what others had done and followed their test methods. I checked the defroster heater for continuity and the defroster thermostat to make sure it was closing. the defroster termostat has to be cold to check it. You will need to check it while it is in ice or t
... Read moreake it out and put it in another freezer for 30 mins and then check it for continuity. Those items checked out ok so it had to be the control board. The control board is a 5 min job to replace but making sure that is your problem is the hard part. I think the control board was bad due to a power surge we had when the power went out and came back on. It might be a good idea to put a surge protector on your home to protect your fridge and all your other electronic stuff. Our refrigerator is now working like new again. Thank you for all your help, Jim
My Orders
