Models > 59655669500

59655669500 Kenmore Refrigerator - Overview

Sections of the 59655669500

[Viewing 16 of 16]

Manuals & Care Guides for 59655669500

Click to download
Keep searches simple, eg. "belt" or "pump".
Light Bulb - 40W – Part Number: 8009
Light Bulb - 40W
★★★★★
★★★★★
(63)
PartSelect #: PS884734
Manufacturer #: 8009
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$7.32
  In Stock
Replacement Ice Maker – Part Number: D7824706Q
Replacement Ice Maker
★★★★★
★★★★★
(139)
PartSelect #: PS2121513
Manufacturer #: D7824706Q
This ice maker (Ice Maker Assembly, Refrigerator Ice Maker) produces ice cubes that are ejected into the storage bucket. It is located in the freezer section of your appliance, mounted on the freezer ...
$132.70
  In Stock
Condenser Fan Motor Kit – Part Number: 833697
Condenser Fan Motor Kit
★★★★★
★★★★★
(30)
PartSelect #: PS395284
Manufacturer #: 833697
This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling the warm refrigerant ...
$53.20
  In Stock
Dual Water Valve – Part Number: WP67005154
Dual Water Valve
★★★★★
★★★★★
(18)
PartSelect #: PS11743618
Manufacturer #: WP67005154
This part, when activated, releases water from the supply line into the ice mold. This water inlet valve is for refrigerators. Water inlet valve supplies water to the refrigerator ice maker and wat...
$95.95
  In Stock
Screw, 8/18 x 3/8 – Part Number: WP90767
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$7.76
  In Stock
Crisper Frame Support – Part Number: WP12603701
Crisper Frame Support
★★★★★
★★★★★
(5)
PartSelect #: PS11738556
Manufacturer #: WP12603701
Support for the crisper or shelf frame. NOTE: If the wall anchor that this mounts to is broken, you will require the related part.
$8.84
  In Stock
Compressor Start Device and Capacitor – Part Number: W10613606
Compressor Start Device and Capacitor
★★★★★
★★★★★
(26)
PartSelect #: PS8746522
Manufacturer #: W10613606
This includes both the run capacitor and the start relay. The capacitor helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. The start ...
$87.83
  In Stock
Door Switch – Part Number: W11396033
Door Switch
★★★★★
★★★★★
(29)
PartSelect #: PS12731166
Manufacturer #: W11396033
This light switch may also be known as a refrigerator door switch or a light switch kit, and is compatible with your refrigerator. The function of the refrigerator door switch is to turn on the light ...
$27.83
  In Stock
Run Capacitor – Part Number: WP65889-4
Run Capacitor
★★★★★
★★★★★
(5)
PartSelect #: PS11743364
Manufacturer #: WP65889-4
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. If you are noticing temperature issues with your refrigerator or freezer,...
$61.94
  In Stock
Light Bulb - 7W – Part Number: W10857122
Light Bulb - 7W
★★★★★
★★★★★
(5)
PartSelect #: PS11731356
Manufacturer #: W10857122
Sold individually. This bulb is a 7-watt appliance incandescent light bulb. This appliance light bulb is two inches long. It is used for many clothes dryers. You will need a Phillips screwdriver and n...
$10.55
  In Stock
Ice Maker Helix End Cap - white – Part Number: WPD7749401
Ice Maker Helix End Cap - white
★★★★★
★★★★★
(9)
PartSelect #: PS11747838
Manufacturer #: WPD7749401
This helix end cap is almost four inches in diameter. It is all white in color and is made of plastic. This end cap is used in a refrigerator's icemaker.
$33.92
  In Stock
SWITCH – Part Number: W11291138
SWITCH
★★★★★
★★★★★
(15)
PartSelect #: PS12584655
Manufacturer #: W11291138
This is a light switch for your refrigerator. It activates when the door of your appliance is opened, and it will turn the light inside on and off. You will need to replace this part is if your light ...
$27.31
  In Stock

Questions And Answers for 59655669500

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the 59655669500

[Viewing 20 of 20]
Ice maker not making ice
Fixed by
these parts
Show All
Leaking
Fixed by
these parts
Show All
Fridge too warm
Fixed by
these parts
Show All
Light not working
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Freezer section too warm
Fixed by
these parts
Show All
Noisy
Fixed by
these parts
Show All
Ice maker won’t dispense ice
Fixed by
these parts
Show All
Not dispensing water
Fixed by
these parts
Show All
Fridge and Freezer are too warm
Fixed by
these parts
Show All
Fridge too cold
Fixed by
these parts
Show All
Fridge runs too long
Fixed by
these parts
Show All
Clicking sound
Fixed by
these parts
Show All
Freezer too cold
Fixed by
these parts
Show All
Ice maker dispenses too little ice
Fixed by
these parts
Show All
Too warm
Fixed by
these parts
Show All
Ice maker dispenses too much ice
Fixed by
these parts
Show All
Freezer not defrosting
Fixed by
these parts
Show All
Won’t start
Fixed by
these parts
Show All
Door Sweating
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of connection held the other two attachment points along the long edge of the icemaker. I did not have repair manual or useful drawing but looked @ PartsDirect pic of side brackets & used a small mirror to confirm that mine were also some sort of "snap in" attachment.
Remove icemaker unit by pushing upward and outward on the unit. I takes a good bit of pressure and will pop loose, but be careful not to break attachment bracket from freezer wall.
Scavenge shut off bar and wiring harness from old icemaker once you have it out & attach to new one before installing it back in freezer.
Again, you might find a mirror useful to align those pesky snap-in brackets with the new unit.
Since you probably kept your freezer running while waiting for the part, the plastic snap-ins will be cold and brittle. I warmed them up first by applying a dampened cloth heated in the microwave to make them a little more pliable.
A good push of the new unit towards the snap-ins along with some upward force will get it stable.
Reattach the metal screw in bracket & connect the wiring harness to rear plug... and don't forget to plug the whole thing back in.
It will take awhile for the first batch of cubes dump as the timer may need to cycle completely around to get to the fill cycle... be patient.
Dump the first couple of batches of cubes just to make sure you're free of any residue.
Parts Used:
Replacement Ice Maker
  • Bernie from Diamond Bar, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
786 of 851 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The compressor would not run.
I removed the screws in the lower back panel where the compressor is located. Then I unplugged the capacitor and plugged the new one in. I then checked to see if the compressor would start. It wouldn't so I replaced the overload relay with capacitor and that fixed the problem. The capacitor just plugs into the relay then plugs into the compressor. There are several screws but all in all it is easy.
Parts Used:
Compressor Start Device and Capacitor Run Capacitor
  • Gilbert from Clinton, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
321 of 366 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water overflowed ice maker turnning ice bucket into solid mass of ice
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: one of the three screws that hold the ice maker to the refrigerator wall is hidden behind the large (black) end of the ice maker and is difficult to access. Before trying to replace the ice maker, make sure you have the physical dexterity to remove that screw. Second problem: it is not apparent how to remove the wire harness that plugs into the ice maker assembly. BEFORE you can remove the wire harness, you MUST remove the large white cap that covers the black end of the ice maker assembly and then push in a retaining tab to release the wire harness. If you don't do this, the wire harness will not release. Other than those two problems, it was relatively easy to remove three screws, unplug the wire harness, transfer three small, metal parts from the old ice maker to the new, plug in the new wire harness, mount the ice maker assembly so that the water tube is in the proper position, and then re-install the three screws. The ice maker works fine now. (P.S. I was told by an expert that the real problem might be a malfunctioning fill valve. I would have replaced the fill valve if replacing the ice maker assembly had not fixed the problem.)
Parts Used:
Replacement Ice Maker
  • Harry from Grand Ledge, MI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
263 of 347 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!