Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 4YED22PWAW00

4YED22PWAW00 Whirlpool Refrigerator - Overview

Get Parts and Repair Help for 4YED22PWAW00

If you know the refrigerator repair part you need, you can browse the list of all parts on the 4YED22PWAW00, or you can search by name or part description. You can also find your part by where it is located on the 4YED22PWAW00 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for 4YED22PWAW00 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.74

Door Cam - Black

The lower door cam is also known as the closing cam or door closer cam and can be found on your refrigerator or freezer door. The purpose of the lower door cam is to lift the door ...

$23.78

Bi-Metal Defrost Thermostat

If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function of the defrost bi-metal thermostat is to clip onto the evaporator and protect your evaporator from overheating during the defrost cycle. If your refrigerator does not defrost properly you can test both the thermostat and the heater to figure out which part is at fault. For this repair, you will need a Phillips screwdriver, a 1/4 inch nut driver, a flat blade screwdriver, a pair of wire strippers, a roll of electrical tape, and a few butt splice connectors.

$65.25

Icemaker Control Assembly

The icemaker control assembly is located in the freezer section of your refrigerator. It is what controls the icemaker. The control turns the timing cams and the ejector blades. It...

$63.28

Thermostat Assembly

This thermostat assembly is used in refrigerator units and freezers as a sensor. The thermostat senses the temperature increase in the evaporator during the cycle of defrosting and turns off when ice is melted. If you have any of the following symptoms, replacing your appliance could solve the problem: fridge does not start, is too warm, too cold, runs too long, or will not start. The tools needed for this repair project is a putty knife, Phillips and flat blade screw driver, 1/4 inch nut driver, and needle nose pliers. Remember to unplug refrigerator from power source as a safety precaution. Refer to the manual provided by the manufacturer for further installation instructions.

$2.96

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

$29.94

Ice Bin Auger Drum

This white ice bin auger drum comes with a washer.

$5.21

Icemaker Water Fill Tube Kit

The icemaker water fill tube provides water to the icemaker so it can produce ice and dispense water. If you notice that your ice maker is not making or dispensing ice, or is leaki...

$14.90

Door Closing Cam Kit

This door closing cam kit is intended for use with the bottom of refrigerator and freezer door hinges. The cam helps with the closing of the doors and to keep them slightly in position when opened.

$16.51

Micro Switch

This switch is located inside the dispenser.

$5.15

Shelf Support Stud

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No ice

  • Customer: Daniel from Suwanee, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 523 of 613 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

inconsistent compressor and condensor fan operation

  • Customer: Steve earney from Brooks, GA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 267 of 279 people found this instruction helpful
Compressor start relay would cycle several times before compressor would come on. Replaced start relay and defrost timer assy. Operated more consistently however not completely reliable. Ice would begin to melt. Noticed that if you would cycle the temperature control the compressor would start again and operate for several hours then not cycle again. Jum... read more

Plastic bits dispensed from Ice Dispenser in Door

  • Customer: john from seaford, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 189 of 202 people found this instruction helpful
Removed Ice bin from Fridge

Removed all bolts on bin with nut driver...about six

Removed housing...be careful with spring on crusher/cube control rod

Removed C clamp on end of auger with small slotted screw driver and needle nose pliers.

Removed plastic nut on end of auger shaft

Removed Ice crusher jaws ... read more