Models > 41761723511

41761723511 Kenmore Washer Dryer Combo - Overview

Sections of the 41761723511

[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Drum Support Bearing – Part Number: 131825900
Drum Support Bearing
★★★★★
★★★★★
(19)
PartSelect #: PS418807
Manufacturer #: 131825900
If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which a...
$8.96
  In Stock
Drum Glide - White – Part Number: 137513300
Drum Glide - White
★★★★★
★★★★★
(15)
PartSelect #: PS5574052
Manufacturer #: 137513300
This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there are two of these in y...
$40.21
  In Stock
Dryer Lint Screen – Part Number: 5304516871
Dryer Lint Screen
★★★★★
★★★★★
(25)
PartSelect #: PS12585473
Manufacturer #: 5304516871
This dryer lint screen is for laundry centers. Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer. Follow the instructions in the owner's manual when installing this part.
$43.42
  In Stock
Thermal Limiter - Limit 220 – Part Number: 134120900
Thermal Limiter - Limit 220
★★★★★
★★★★★
(13)
PartSelect #: PS419402
Manufacturer #: 134120900
The dryer thermal limiter, also known as a thermal fuse, blows the fuse to cut off power to the dryer when the dryer begins to overheat. Once the dryer reached 220 degrees Fahrenheit, the heat cuts ou...
$27.14
  On Order
Door Catch – Part Number: 131658800
Door Catch
★★★★★
★★★★★
(18)
PartSelect #: PS418433
Manufacturer #: 131658800
The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, which allows the door...
$58.17
  In Stock
Multi-Rib Drum Belt – Part Number: 137292700
Multi-Rib Drum Belt
★★★★★
★★★★★
(12)
PartSelect #: PS3408299
Manufacturer #: 137292700
The multi-rib drum belt is also known as a drive belt and is a part for your dryer. The function of the drum belt is to attach to the motor pulley. It will then spin the drum as the motor rotates. Ove...
$20.15
  In Stock
Lower Front Felt Seal with Adhesive – Part Number: 5303937183
Lower Front Felt Seal with Adhesive
★★★★★
★★★★★
(6)
PartSelect #: PS832645
Manufacturer #: 5303937183
The lower front felt seal with adhesive, also known as a drum felt seal, is used in dyers and allows the drum to easily glide on the front panel. For this repair project, you will need the following t...
$29.90
  In Stock
Dryer Drum Bearing Bracket – Part Number: 131724301
Dryer Drum Bearing Bracket
★★★★★
★★★★★
(2)
PartSelect #: PS12579101
Manufacturer #: 131724301
This drum bearing bracket is for dryers. Drum bearing bracket holds and supports the drum bearing
$10.50
  In Stock
Ball Hitch – Part Number: 131777700
Ball Hitch
★★★★★
★★★★★
(1)
PartSelect #: PS418736
Manufacturer #: 131777700
This ball hitch provides support to the drum located at the back wall of the dryer. This allows the drum to spin. The bearing may have gone bad and you might notice that the ball is cut off. The ball ...
$69.82
  In Stock
High Limit Thermostat – Part Number: 3204267
High Limit Thermostat
★★★★★
★★★★★
(2)
PartSelect #: PS446428
Manufacturer #: 3204267
This high limit thermostat is used in a dryer and monitors the temperature to make sure it does not exceed 260 degrees Fahrenheit. When your dryer temperature reaches 260 it will cut it out and only c...
$85.14
  In Stock
Front Upper Felt Seal with Adhesive – Part Number: 5303937182
Front Upper Felt Seal with Adhesive
★★★★★
★★★★★
(3)
PartSelect #: PS832644
Manufacturer #: 5303937182
The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so t...
$24.71
  In Stock
Screw-In Plastic Leveling Leg – Part Number: 134548800
Screw-In Plastic Leveling Leg
★★★★★
★★★★★
(4)
PartSelect #: PS1152204
Manufacturer #: 134548800
This is a screw in leveling leg for your washing machine. It supports the appliance by screwing in place to create a stable and flat surface. Take note that you are able to adjust the height of your a...
$25.68
  In Stock

Questions And Answers for 41761723511

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the 41761723511

[Viewing 10 of 10]
Noisy
Fixed by
these parts
Show All
Door won’t close
Fixed by
these parts
Show All
No heat or not enough heat
Fixed by
these parts
Show All
Will not tumble
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Marks left on clothes
Fixed by
these parts
Show All
Too hot
Fixed by
these parts
Show All
Takes too long to dry
Fixed by
these parts
Show All
Shuts off too soon
Fixed by
these parts
Show All
Leaking
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Thermal Limiter opened
Unplugged Dryer.
Opened top of Dryer, over the drum.
Removed Thermal Limiter.
Tested the Thermal Limiter - found it was open.
Checked all vents and exhaust tube for lint build-up.
Replaced Thermal Limiter.
Closed top of dryer.
Plugged Dryer back.
Tested Dryer - it works.
Parts Used:
Thermal Limiter - Limit 220
  • Stephen from Newnan, GA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
237 of 309 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
squeeking like crazy
well, i started at the top and worked my way down. by taking the top off, it gave me more room to get the dryer tub out. took the two screw`s out of the vented plate on the back of the machine to undo the belt. this is a stackable washer-dryer combo, so next i took off the white plate on front between washer & dryer. took off the control panel, unpluged it, then took dryer door front off. then removed the two screw`s that hold that bracket on ,in the back of dryer, pulled the drum out & replaced the belt, but before replacing anything i took the shopvac to it , there was alot of lint in there.when replacing the Grounding Ball Clip & Grounding Ball, i took a one inch by two inch magnet and used it to hold the Grounding Ball & Clip in place so i could get the two screws started in the Drum Support Bearing & Bearing Bracket. after installing that i put the shaft in place & lined the dryer tub up with the 3 screw hole`s ,and boom, bang, pow...nothing to it. it`s easy...parts came very fast....Thx PartsSelect.com...i`ve told all my friend`s about PartsSelect
Parts Used:
Multi-Rib Drum Belt Grounding Ball Clip Grounding Ball Drum Support Bearing Ball Hitch Dryer Drum Bearing Bracket
  • Steve from Wheelersburg, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench set
126 of 144 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not start
I found a electrical diagram and some common problems on some websites which led me to check the thermal limiters. There are two right up top near the back of the dryer - one mounted closer to the heating coils and one mounted directly to the sheet metal on the inside back of the dryer. Using an DMM on the "Ohms" setting, I checked each sensor to make sure that they were "closed" (near zero ohms). Sure enough, the sensor mounted on the back of the enclosure was open (high resistance) which prevented the dryer from starting. To confirm, I shorted the two leads going to the sensor together temporarily and wrapped them with electrical tape and then tested the dryer - it worked perfectly. The part from Part Select was ordered and shipped very quickly. Since the sheet metal screws holding the sensor on were difficult to access with the drum in place, I used small machine screws/nuts to fasten the sensor - this allowed me to tighten the nuts from the outside of the dryer, making it very easy to attach.
Parts Used:
Thermal Limiter - Limit 220
  • Stephen from Austin, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
96 of 101 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!