Models > MDE9206AYW > Instructions

MDE9206AYW Maytag Dryer - Instructions

All installation instructions for MDE9206AYW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDE9206AYW
61-75 of 604
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The dryer drum would not rotate when the start button was pushed.

  • Customer: Bruce from Gladstone MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 3 of 3 people found this instruction helpful
First this I did was to disconnect the power cord. Then I removed the screws that held on the door and the two on the other opposite side. This allowed the front panel to be removed. Next I removed the top two screws which allowed the top to hinge up and out of the way. Then I removed the rest of the screws that held the front drum support and moved it to the side. I did have to unclip the wires that ran to the interior light. I did not how ever have to disconnect any wires at the front of the dryer. Next I reached in from the bottom of the drum and released the drive belt from the spring loaded pulley. at this point the drum was able to be removed out the front of the unit. This gave access to the motor. It was necessary to remove the several screws that held on the front half of the fan housing. Again I did not remove any wires as this too could be moved to the side out of the way. I then removed the snap ring and clamp from the fan end of the motor shaft and pulled the fan off of the shaft. Next I unclipped the wiring connector from the top of the motor and used a screw driver to pry the connector off. Next I used a socket on a long extension to push down on the motor clamps while tilting the socket out to allow the clips to release. I then removed and replaced the motor and assembled in the reverse order. While I had the drum out I inspected the rear support wheels and noted that one would hardly turn. I removed both wheels via a nut on the back side of the shafts. I found that one had shifted on the bushing and was making contact with the frame. I used a vise to press the wheel back into the correct location. I also applied anti seize with a small amount of dry graphite to both wheels and insured that the both rotated freely. I then installed the front two glide slide pads using the pop rivets provided in the kits. I used a shop vac and cleaned any lint from inside the dryer. I then reassembled the front covers in reverse of the disassembly process. I rotated the drum by hand prior to applying power. I also ran the unit with the heat off for the first five minutes. Total cost was under $160.00 or half of the replacement cost.

Dryer baffle broke when drying sneakers

  • Customer: Chad from West Fargo ND
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 4 people found this instruction helpful
I was able to quickly make this repair with the help of some instructions that I found on this site on how to remove the front panel of my dryer. 4 screws on the front around the door (and removal of the door) and then it was simply a matter of rolling the top portion out to pop it out of some clips and then the front panel opened toward me and I was able to lift it off of the metal fingers that secure it on the bottom. Removing the old baffle was a matter of removing two screws with a nutdriver and installation of the new baffle was a breeze. All in all I was done start to finish in under 10 minutes.

Heater ran constantly, except in air fluff cycle, thus operating extremely hot

  • Customer: Charles from Mount Storm WV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 7 people found this instruction helpful
Removed the frong cover and and internal sheild, removed and replaced thermostatic, wiring as original.
I had searched several other sites first for thee part, but none of them seemed accurate. Your photo matched the old exactly, giving me the confidence I wanted before ordering.

drum support roller was squeaking

  • Customer: Kevin from San Diego CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 2 of 2 people found this instruction helpful
My 11 year old grandson and I did the repair together. He had a blast and I did too. First we removed a bunch of screws that got us no closer to getting the machine apart than when we started. Then I remembered from the last time I had the machine apart that there are two screws just below the door, angled as not to be visable unless you know where to look. Once we removed those the from came off. We removed the wires for the door light and heat sensor, remembering the order of the wires for later reinstallation. Then we undid the bolts holding down the top. Once the top was removed we took off the belt and removed the drum. We used the retainer pliers to remove the retainer ring from the first roller. We removed the roller and also the shaft as this roller was the noise maker and the shaft was not in reusable condition. We installed a new shaft, roller washer, roller, another roller washer and then the retainer ring. We repeated the same process on the other roller, although we did not replace the shaft as it was in good condition. It turned out I did not need to order the shaft washers as the rollers came with washers. Oh well, its not a good job unless you have parts left over when you are done. Once we replaced the rollers we commenced reinstallation. But first we had to google for diagram of the proper belt installation, which we found and that got the drum and belt installed properly. Thankd god for the internet. Once we had the drum installed we put the machine back together in the opposite order we took it apart. An operational test showed we did the job right, no more squeaking. The only injury was my grandson cut his thumb right after I gave him the speech about watching where your hand is going to end up when that bolt breaks free. It broke loose and into the metal bracket went his thumb. Oh well it was a good lesson and it was not a bad cut. All in all a good repair.

belt tensioner pulley seized to shaft

  • Customer: Shane from Heber City UT
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 2 of 2 people found this instruction helpful
At first I thought I could just replace the pulley, but on closer inspection I found that the pulley had become seized on the shaft. I ended up removing the entire bracket (which I should have purchased also) and cutting the shaft off. I manufactured a new shaft from a bolt of the appropriate size and tack welded it to the bracket. It took a little more time than I anticipated. My advice to anyone doing this would be to spend a little extra money and buy the entire bracket and pulley. That would make this about a 15 minute job.

Blower wheel over time became clogged w/lint & caused the dryer to vibrate

  • Customer: Carol from Onsted MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 5 people found this instruction helpful
Removed the dryer front, then detached the retainer ring holding the blower wheel in place. Set the new blower wheel, attached the new ring retainer and placed the dryer front back in place. Thank you for the low prices - I searched on-line at 3 sites and you were the best price available.

Dryer would start when pushing start button

  • Customer: Scot from Apopka FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Removed the control panel disconnect the wires on the bad part and replaced with new. Extremely quick and easy less than 10 minutes. Part ordered on line and received within one day.

Squeaking noise while spinning

  • Customer: Thurman from Huntsville AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
removed dryer door 4 screws
removed front panel
removed front tumbler bracket
removed blower cover
removed wires attached to heat and door sensors
removed top
removed drum and belt
removed side panel
removed clamp holding idler pulley
replaced pulley and clamp
reversed above steps

Broken lint filter

  • Customer: Gwenda from Anahuac TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
All I had to do was replace it. Just wanted to say what curteous service I received and how PartSelect kept me informed of the status of my order through email. Thank you!

NOISEY BEARING ON SUPPORT ROLLER

  • Customer: A from Des Plaines IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
UNPLUG UNIT FROM WALL.REMOVED FRONT COVER,2 SCREWS AT BASE.
REMOVED CLIP HOLDING ROLLER ON SHAFT.
THEN REALISED FRONT DRUM SUPPORT WOULD HAVE TO BE REMOVED,4 HEX HEAD SCREWS. tHIS ALLOWED DRUM TO BE MOVED FORWARD TOWARD FRONT TO ALLOW REMOVAL OF ROLLER AN INSTALLING NEW ONE.

Loudly squealing dryer

  • Customer: Donald from Bridgewater MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
Piece of cake. Use the available manual to ascertain dismantling procedure. Only thing that might be tough for average DIY'er is the internal snap rings. Snap ring pliers are mandatory for quick easy repair.
Total time was probably about 15 minutes and this was the first time I had taken it apart. Quiet as a mouse now!
Very helpful site.

Our timer dial had been broken for some time, cracked around the connection to the control panel. I had been able to epoxy glue it to where it was functional, but that eventually failed. We were using a pair of pliers to set the timer on the dryer.

  • Customer: Joanne from Missouri City TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
I was able to easily find the replacement part on PartSelect, and the schematics showed me how to easily disassemble my dial (which has three parts) so that only the broken part needed to be replaced. I used a tiny straight-slot screwdriver to pop the pieces apart. Once we received the new piece, it was very simple to pop the pieces back together and have a fully functioning new dial!

End of one baffle pulled away from drum

  • Customer: Kim from Jacksonville FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 2 of 2 people found this instruction helpful
Following the instructions I pulled off the door and front panel. After rotating drum so the broken baffle was at the bottom I used a socket to remove the two screws on either end. I removed the broken baffle and inserted the new baffle in its place. Reinserted the screws, front panel, and door. I do strongly suggest having the manual handy to view the steps. It's available in PDF format.

Buzzer didn't work

  • Customer: Jack from Oro Valley AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 5 people found this instruction helpful
Unplug dryer--remove back panel of control console--swap out buzzer--cover back--plug in--good to go.

Dryer stop signal noise(BRRRRRTTTTTT) would not quit! Had to open door to stop the noise.

  • Customer: KEN from CLIFTON TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Removed back cover of console,using screwdriver and nut driver. Removed old switch by squeezing the end tabs and pulling switch out. Removed wires on switch with pliers. Placed wires on new switch using pliers. Snapped new switch back in place. Replaced back cover to console with screwdriver and nut driver.
All Instructions for the MDE9206AYW
61-75 of 604