Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS1854703
Sold individually. This part is located beneath the element and catches any spills.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
This trim ring is intended for use with many electric ranges. It is a chrome trim ring that is used with six inch surface burner elements. Notes The matching eight inch chrome trim ring is available with part number PS120222.
This trim ring is used with many electric ranges. It is a chrome trim ring that is intended for use with eight inch surface burner elements.
This drip bowl is eight inches in diameter. It is made of black porcelain.
This black porcelain drip bowl is six inches in diameter and it has a vent hole.
All I did was take out the old drip bowls and broken element and put in the new. I have had a difficult time trying to find the parts, but PartSelect made it so easy and the parts were the correct ones for my old JennAir stove.
Help other customers find the most helpful instructions.
Were these instructions helpful?
This was so easy. I've looked for years in stores for these pans. I finally tried the Internet, found PartSelects and, holding my breath at what i'd find, voila'...perfect fit, perfect replacements. And it took just a couple days to arrive. I'll definately be back! /John
just replaced by hand .
Replaced the drip pans
Pulled out the old burner and plugged in the new!
The repairs were very simple we just disconnected one screw then removed the old one and replace with new one. The left side took a little longer, because of the 8 screws we needed to remove to take the back panel off. But once we had it taken off the replacement was a snap. Nothing to it.
No brain surgery required. Removed electric burner, put in new drip pans. Voila! Good for many more years of service looking like new.
replaced drip pans--they fit perfectly and look great!
Just remove the old ones and replace them with the new ones. no tools necessary.
Unplugged the burner units and replaced the drip pans. Five seconds time per burner.
Removed screws by drilling one and using a pliers to remove 2nd one. At first did not have enough wire to pull recepticles out until I relized wires were clipped to back of range to hold in place. Unclipped wires, pulled recepticles out, cut wires and attached new recepticles by connecting wires with wire nuts (I think wire nuts were to small so I used my own a size larger). Another problem that I found was that the recepticles on my range were held in place only by the screws that attached the recepticles to the drip pan flang. I had to bend an L bracket to prop under each recepticle to hold the back of it up so the burner element would sit level over the drip pan.
I just pulled the electric element out of the slot and dropped the drip pan in place and slipped the electric element back in place and it was ready to go. It looks almost new. We built a new house in 95. It took 17 months to build it. I got the stainless steel cook top that you can have the grill on one side or you can pull the grill off and slip in the burners. It is only 4 burners but it is plenty to work with. It has a down draft.
couldn't find replacement in our town, which is quitesmall and no Maytag dealers. So, I ordered on line two drip bowls and saved one"just in case"Mission accomplished. Thanks allot.
Pulled the old one out and slid the new one in (and replaced the drip pans at the same time). Very easy.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.