Quick Question!

Have you ever purchased from PartSelect.com before?

http://www.partselect.com/Schematics/Maytag/49999.gif
See part 3 in the diagram
http://www.partselect.com/Schematics/Maytag/49999.gif

Electronic Clock Control Board

PartSelect Number PS11743858

This electronic board is located within the control panel.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not program.
  • Will Not Start.
  • Touchpad does not respond.
  • Timer will not advance.
  • Little to no heat when baking.

Compare At

$449.78

You Save

$74.96

Your Price

$374.82
$60
Recycling Rebate
Order within the next 41 mins and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 108 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Richard from Ellijay, GA

Clock assembly very dim, hard to read

Remove four screws behind control knobs. Remove four hex nuts under control panel (open oven door to locate). Pull control panel down and out. Remove two hex nuts holding clock assembly. Remove three wire connectors on the old clock assembly and carefully insert on new clock assembly. Reverse instructions to re-assemble. It's a breeze to do! Took longer to get my tool box than the time it took to replace the clock assembly.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Wrench set
Customer: Craig from lexington, KY

Clock would restart and controlls would stop working

This is the second clock I have had to put in this unit in about that many years. The first time I disassembled far to many things. This time I knew to only unscrew the front panel and side triangle plates. The process was much faster the second time. I hope this is not a chronic problem though.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Dennis from Scottsdale, AZ

Led display to dim to read

I first turned the breaker off. Then removed the screws under the display with the oven door open. Then removed the side screws. Then removed the trim kit for the microwave which exposed 3 more screws. The middle one with the Micro Door open. The complete display panel then was removable. I took a digital picture of the 2 wire and 1 ribbon connectiors (I know-anal). Then removed the 2 wire groups-struggled somewhat with the ribbon connector until I realized by trial & Error that the 2 little tabs on the sides only pull upward, releasing the ribbon. Removed 4 nutdriver screws to remove old display-installed new one in reverse fashion. Then I CLEANED everything I could reach it was so dirty! (I live in the desert,duh!) I just paid great attention to how it came apart and it was relatively easy. The best part is that I didn't have to remove the Oven/Microwave unit to do the repair.The new part works perfectly, thanks!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools:
Customer: Edward from Rohnert Park, CA

Readout dimmed to nothing

piece of cake KILL POWER AT BREAKER BOX. Remove burner knobs exposing 4 screws. Open oven door exposing 4 philips srews, four 1/4 hex head screws, and 2 philps screws for end caps. Had to pull out range about an inch (less) away from countertop. Remove screws. Move end caps away from face plate.Pull out face plate. Pull down / out bottom plate to expose Assembly. Unclip wire connection, carefully pull out ribbon connection. Remove 2 screws. Install in reverse.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Paul from Newcastle, ME

Clock faded while stove and oven still worked

Turned off the breaker. Removed the screws under the front panel and eight screws behind the burner controls (two each). I then slid out the panel and laid it flat on top of the stove. Removed the three connectors. Most difficult was the ribbon connector: Squeeze the clips at each end and slide the top half of the connector up. Then the ribbon slides out (practice on the new part). Only two screws held the assembly in. Reverse the process with the new assembly. Worked great!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Karl from Rockford, MI

Fading display

My microwave is stacked on this stove. I had to pull cover off to slide part off. screws were a snap. only problem was the slip catches on the ribon strips. Sperating with flat head was scary but worked fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Geoff from Madison, CT

Display dimmed to nothing

unscrewed the top face plate assembly disconnect 2 wire harnesses 4 screws to release display clock 1 wire harness and then reverse order

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Ila from Carthage, NC

Clock light was out. Oven worked but it was a guess that I could not see the temp

Cut of electricity. Opened the oven door and removed some screw that were over the door that let a plate be removed. Then that let the part drop down that was holding the clock. I removed 2 screws that was holding the clock in place, unplugged the 3 connectors that feed the clock, attached the 2 screws back in that held the clock, put the part back up in place, added the plate and was done. Turned the power back on. I was delighted when I saw the clock light on. Easy to install.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: John from Hadley, MA

Time and temp not displaying

I have only two things to add to the other repair stories on this site: (1) Unlike the ribbon cables inside desktop computers, the ribbon cable on this range is entirely separate from the connector, which is permanently attached to the clock assembly. There are clips on the top of the connector at each end. Push them in and raise them gently to release the ribbon cable. (2) There are two Molex connectors attached to the clock assembly. The pins for one of them were bent on the new clock assembly I received. Before installing it, I spent some time gently coaxing those pins back into alignment. Use your fingernail, and be patient.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Bob from san jose, CA

Display burned out

Very simple. A few screws removed, disconnected a few wires, reattached the wires, put back the screws all without a single cuss word

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Robert from West Columbia, SC

Very dim display

Loosened the contol panel until I was able to get to the Digital Display board.
Removed the three cables and the screws that held the display unit to the control panel.
Reversed the procedure to instll new digital clock display unit.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Vick from Arlington, VA

Oven led display blank

Open oven door
Remove two sets of four screws underneath the LED display
Remove stove handles (pull off easily - no tools needed)
Lower flat plate width of oven and about two inches deep should be able to drop out from under the clock display.
Remove face plate over clock.
Unscrew four screws holding clock unit down.
Undo two electric connectors and the thin ribbon connector - the thin ribbon connector is different - the ribbon comes loose and the black plastic connector stays in place on the board.
Press the thin ribbon connector ends inward and pull up to detan ribbon on old one and then to insert ribbon on new one.
Reverse the rest.
Not too bad!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Joel from Decatur, GA

Clock faded out until you could no longer see it or the oven temp

Turned power off to oven, removed control knobs, took out four screws under panel. Removed four 1/4" sheetmetal screws. Removed front cover, Removed two additioanl screws that held front cover to corner bracketts, Removed two screws that held clock to plate, removed each wiring harness and pluged into new part, unplugged wiring ribbon from old part plugged into new. reassembled. Turned power back on and tested and we had light!!!One repair company was going to charge us over $400 to make this repair!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: James from Virginia Beach, VA

The control paned lights went completely out over time.

Turned off power to stove
Removed control knobs and retaining screws under the knobs.
Opened oven door.
REmoved screws (4) holding the face plate to the stove.
pulled the panel downwards.
Unscreewed clock circuit board.
Removed connectors (3) (See Below)
NOTE the flat ribbon needs to be removed by pinching the ends of the black connector , liftiing and GENTLY pulling the ribbon out of the connector. The black connector remains on the circuit board.
When in stalling the ribbon, pinch the ends of the black connector and lift slightly, insert ribbon, then push down on the loose side of the connector until it snaps shut ,forming a tight connection.

Reverse steps

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Nancy from Naperville, IL

Clock and oven display were extremely dim.

Turn off power to the stove. Pop off the burner knobs and remove the screws attaching the controls to the front panel. Open the oven door and remove the four screws attaching the panel to the oven frame. The panel slides down giving easy access to the circuit board. Remove the two connectors and the ribbon cable attached to the board. There are small clips on the side of the ribbon cable connector that release the ribbon cable. Unscrew the board and install new board. Reattach the cables, put the panel back in place and attach. Reattach the burner controls to the panel, pop the knobs back on, power the stove back on, put on a pair of sunglasses to view the now blazingly bright display and admire your work.

Help other customers find the most helpful instructions.

Were these instructions helpful?