Models > SCE30600BC

SCE30600BC Jenn-Air Range - Overview

Get Parts and Repair Help for SCE30600BC

If you know the range repair part you need, you can browse the list of all parts on the SCE30600BC, or you can search by name or part description. You can also find your part by where it is located on the SCE30600BC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for SCE30600BC parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.58

Light Bulb - 40W

Sold individually.

Order within the next 3 hrs and your part ships today!
$28.12

Long Oven Sensor

This oven sensor kit comes with two harness adapters. This sensor detects the temperature within the oven cavity.

Order within the next 3 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 3 hrs and your part ships today!
$59.24

Infinite Switch - 240V

This part is used for the 6" and 8" burners. Note: This part has been updated by the manufacturer. It may differ in appearance but will still function the same.

Order within the next 3 hrs and your part ships today!
$43.04

Bake Element - 240V

The element has male terminals. This bake element is found on the bottom of the oven.

Order within the next 3 hrs and your part ships today!
$18.07

2 Piece Broiler Pan

The top of this part is now black.

Order within the next 3 hrs and your part ships today!
$40.45

Dual Surface Burner Switch Kit

This switch is used to operate the dual surface burner.

Order within the next 3 hrs and your part ships today!
$60.64

Surface Element Kit with Limiter - 6"

This ceramic element kit comes with an overheat limit switch, two wires, and two wire connectors.

Order within the next 3 hrs and your part ships today!
$43.83

Oven Rack

Sold individually.

Order within the next 3 hrs and your part ships today!
$28.13

Light Lens

This part goes over top of the light bulb.

Order within the next 3 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 88 of 101 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

Outer element of dual element burner didn't work

  • Customer: Michael from Collierville TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 90 of 119 people found this instruction helpful
Remove Ceran Galss top by removing hex screws below the rim. Also remove the two opposing screws in the center of the downdraft opening. Ceran top comes off easily now.
The instructions with the new switch were very poorly written, so here is how I got the new switch to work:
Attach the black wire(s) from the old switch (terminal 2) to the new sw... read more

Lost all clock and timer display

  • Customer: John from Kuna ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 63 of 68 people found this instruction helpful
Removed the 4 phillip head screws that hold the trim plate on the bottom of the display panel (and you probably could skip this step).
Next, I removed the knobs from the front of the display panel.
Then I removed the 4 phillip head screws that were located (1 each) behind the knobs.
Finally, I removed the 4 hex head screws from the bottom of t... read more