Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SCE30600B Maytag

SCE30600B Jenn-Air Range - Overview

Get Parts and Repair Help for SCE30600B

If you know the range repair part you need, you can browse the list of all parts on the SCE30600B, or you can search by name or part description. You can also find your part by where it is located on the SCE30600B by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for SCE30600B parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

$29.46

Long Oven Sensor

This oven sensor kit comes with two harness adapters. This sensor detects the temperature within the oven cavity.

$84.13

Surface Element with Limiter - 6" - 1200W

Sold individually.

$42.42

Dual Surface Burner Switch Kit

This switch is used to operate the dual surface burner.

$22.22

2 Piece Broiler Pan

The top of this part is now black.

$69.92

Surface Element Kit with Limiter - 6"

This ceramic element kit comes with an overheat limit switch, two wires, and two wire connectors.

$44.36

Inner Oven Door Glass - Single Glass

The manufacture has substituted this part to a single piece of glass. Must use original window frame when replacing this part.

$18.69

Leveling Leg

This leveling leg is sold individually. It is all black in color and is made of a hard plastic. Four of these are required per range.

$106.21

Dual Radiant Burner Element with Limiter

$333.10

Electronic Control Board

This board comes with the metallic shield.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Right rear burner went bad

  • Customer: Mark from Loxahatchee, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 105 of 113 people found this instruction helpful
Turned the breaker off, I removed 2 screws securing the range top to the range, opened the top and secured it in the up position, Removed the 2 screws securing the element ,one at a time I swapped the quick connectors from the old element to the new and repeated the process in reverse. I save over $100.00 in labor, plus most companies get you for a trip char... read more

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 107 of 123 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

Outer element of dual element burner didn't work

  • Customer: Michael from Collierville, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 104 of 135 people found this instruction helpful
Remove Ceran Galss top by removing hex screws below the rim. Also remove the two opposing screws in the center of the downdraft opening. Ceran top comes off easily now.
The instructions with the new switch were very poorly written, so here is how I got the new switch to work:
Attach the black wire(s) from the old switch (terminal 2) to the new sw... read more