Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SCE70600W

SCE70600W Jenn-Air Range - Overview

Get Parts and Repair Help for SCE70600W

If you know the range repair part you need, you can browse the list of all parts on the SCE70600W, or you can search by name or part description. You can also find your part by where it is located on the SCE70600W by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for SCE70600W parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

Order within the next 3 hrs and your part ships today!
$29.46

Long Oven Sensor

This oven sensor kit comes with two harness adapters. This sensor detects the temperature within the oven cavity.

Order within the next 3 hrs and your part ships today!
$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

Order within the next 3 hrs and your part ships today!
$22.22

2 Piece Broiler Pan

The top of this part is now black.

Order within the next 3 hrs and your part ships today!
$52.03

Bake Element - 240V

The element has male terminals. This bake element is found on the bottom of the oven.

Order within the next 3 hrs and your part ships today!
$71.56

Surface Element Kit with Limiter - 6"

This ceramic element kit comes with an overheat limit switch, two wires, and two wire connectors.

Order within the next 3 hrs and your part ships today!
$43.60

Oven Rack

Sold individually.

Order within the next 3 hrs and your part ships today!
$61.61

Broil Element

This broil element is found on the roof of the oven.

Order within the next 3 hrs and your part ships today!
$50.55

SEAL- DOOR

This oven door gasket prevents heat from escaping the oven cavity when in use.

Order within the next 3 hrs and your part ships today!
$374.82

Electronic Clock Control Board

This electronic board is located within the control panel.

Order within the next 3 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Right rear burner went bad

  • Customer: Mark from Loxahatchee, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 106 of 114 people found this instruction helpful
Turned the breaker off, I removed 2 screws securing the range top to the range, opened the top and secured it in the up position, Removed the 2 screws securing the element ,one at a time I swapped the quick connectors from the old element to the new and repeated the process in reverse. I save over $100.00 in labor, plus most companies get you for a trip char... read more

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 110 of 127 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

Lost all clock and timer display

  • Customer: John from Kuna, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 75 of 81 people found this instruction helpful
Removed the 4 phillip head screws that hold the trim plate on the bottom of the display panel (and you probably could skip this step).
Next, I removed the knobs from the front of the display panel.
Then I removed the 4 phillip head screws that were located (1 each) behind the knobs.
Finally, I removed the 4 hex head screws from the bottom of t... read more