ZISW48DXA General Electric Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The auger in the ice bucket was rusted
Removed 4 screws from the old rusted ice bucket ( they hold the cover on) installed the cover and screws in the new ice bucket and installed the new unit in the freezer .
Parts Used:
-
Frank from Temecula, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Put the part in and observed water leaking from the ice maker which caused the cup to break
Ordered new Ice Maker from you and fixed the problem completely.
Parts Used:
-
John from Ravenden, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
no ice
-
Richard from Las Cruces, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Not dispensing water
I watched the video on the partselect website once and completed the repair. Very easy!
Parts Used:
-
Anthony from Orlando, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
The ice dispense door flapper was deformed letting warm air into the freezer compartment.
The trim piece covering the opening of the dispenser is the first and most difficult part of the disassembly. Take care when removing this piece that it does not break.
Parts Used:
-
David from Kennesaw, GA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
actuator pad it was broken
just i took off the actuator and replace with the new one in 8 minutes.It was so easy.
Parts Used:
-
JULIO from LOS ANGELES, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Would Not Dispence Ice
Watched video on the parts order information page and did the repair. Very helpful made me feel like I could do the repair
Parts Used:
-
Richard from Garland, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Frezzer would freeze up, refrigerator stayed cold, solved the problem. Now the refrigerator seems to be running more than usual.
Checked the defroster coil which is located behind the rear panel in the freezer compartment, it was still working. Followed the schematics down to the defrost timer, which is located in the lower front of the refrigerator and tried that. Plugged in the new part and the problem is solved.
Parts Used:
-
Henry from West Seneca, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Refrigerator was only dispensing crush ice and not cubes
Solenoid pushing the crushed ice flapper was burned out. Solenoid was easy to find unplug and replace. I used the old piston which simplified things. Now works great
Parts Used:
-
Charles from Spring, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ice maker was spewing water into freezer
Ordered this part after i replaced the plastic tubes on the back as the problem persisted. loosen the nuts holding the water inlet lines, remove the cover to the valve. remove the valve and the water inlet line to the the valve. Disconnect the 2 outlets from the valve. 1 outlet to icemaker and other outlet to water cooler (bigger). Connect water inlet and 2 outlets to the new valve, test the water lines. Found the inlet is leaking, removed it and added teflon tape and reconnect it. All is done. Then I left the freezer door open for 3 hours to melt the ice on the wrong places and all is well.
Parts Used:
-
andy from clearwater, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Flapper valve allowing frost/ice to accumulate in chute in summer
Followed the online video exactly and it was easily done. Couldn't have been better. The problem is solved.
Parts Used:
-
Richard from Dumfries, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
A previous repairman removed the circuit board and never returned!
We watched the video and it was super easy! Once the circuit board was replaced, everything worked perfectly! Thanks so much for helping us keep this refrigerator in working order!
Parts Used:
-
Roger from Brady, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ice maker was leaking water. Cubes were sticking inside tray.
Reviewed video which was very helpful. Loosened two philips head screws, lifted up ice maker, unpluged power suppy and reinstalled. One of the easiest replacements ever!!
Parts Used:
-
Carl from Abilene, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Parts Used:
-
ANTHONY from NEW EGYPT, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice forming on dispenser chute
I disconnected power to the refrigerator. Pried the face plate plate off the front of dispenser(plastic plate that has symbols for ice, water, light). Removed four screws. Gently removed and unplugged dispenser controller (You have to remove the rubber cover of the actuator - it pops off). Removed one screw to dispenser assembly crank. Assembled flapper, spring, and crank. Re-assembled in reverse order.
Parts Used:
-
David from Choctaw, OK
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!