ZISW48DXA General Electric Refrigerator - Instructions

Remove front outside cover with the pictures on it. It is held in place with 5 push type pins. Remove the ice holder or turn off the power to keep the auger from running. Remove the four screws that hold the solenoid assembly and unplug the power plug. Remove the screw and small plate that holds the flapper assembly in place. Install the new flapper and spring and re-install the other parts. My flapper was loose in the holder causing the top of the flapper to hang on the hole in the ice outlet. I installed a small screw through the back of the holder to secure the flapper.

Removed the old ice bucket assembly and dumped the contents. Removed four screws from the face plate and reinstalled it to the new ice bucket kit. Back in business.

Defrost timer is hidden in the control panel in the refrigerator top middle. Turn to off and remove two screws which are hidden behind white tabs. I had to pry the old timer from the plug with a screw driver because it was tight. Try not to short across the terminals. Plug in the new timer. Replace it in the clip where you got old one and reinstall the controls. The freezer was still all frosted up so I had to remove the cover and defrost it with a hair dryer to get it to work. Then I turned it on and it works great.

unscrew one screw unplug.insert the ice maker,put the screw back in you have ice less than ten minutes

Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.

Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.

Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....

took 1 screw out and removed ice maker and slid new one in and replace screw and connected power cord

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

I pulled the Refrig out of the space so that I could get to the plug and water shut off. After unplugging and turning the water off, I had to remove the 7 screws holding the cardboard cover over the bottom portion of the Refrig. I then had to unloosen the water input to the the valve. Then I removed the screw holding the Water Valve. I then had to unplug the unit from the electrical connectors. After that I had to cut the plastic hoses off the valve. All that was left was to reconnect everything, replace the cardboard covering and do an operational test. Everything worked. The ice maker began to produce ice cubes and there were no leaks.

Follow PartSelect video on website, had no problems learned a lot

I am more than 80 yrs, always thought I could fix just about everything--but, this looked complicated. Once I received the new icemaker; took a good look where the screw-holes, etc. were, then removed the "old" one. Took about 20 or 30 minutes, then the "new" one was easily installed.

parts select delivery time unreal !!!!! ordered on a Tues. was here Wed !!!! Perfect fit, minor difference in tubing connection. Took more time to clean the floor once i moved the fridge than the actual repair. Thank you Parts Select, if i need more appliance repair parts, you're my first choice>

Washed new Ice Bucket assembly with dish soap and warm water, and let dry. Removed (4) small screws holding Ice Bucket Door assemby to my original Ice Bucket assembly. Reinstalled Ice Bucket Door assembly to new Ice Bucket.

opened back panel and replaced valve verry easy