Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer Baffle broke off and rear felt seal was pulled out
1. Remove 2 screws that hold door hinges on. 2. Remove 2 screws on opposite side of door hinge and remove 2 plastic clips. 3. There are 2 hex screws that hold the front panel on. Remove these and the panel is held on by a flex clip. Gently twist the top towards the outside of the dryer and they will come free. 4. tilt panel forward and lift of 2 clips at the bottom. 5. Remove the screws under the cover panel which will release the drum holder and lint collector. 6. Lift top of dryer and lift out drum. TAKE THE TIME SINCE THE UNIT IS OPEN TO VACUUM OUT THE ENTIRE DRYER. CLEAN OUT THE EXAUST TO IMPROVE EFFICIENCY AND SAFETY. 7. I replaced the rear felt by using a flat head screwdriver to lift tabs and install felt. Using the screwdrive I compressed the tabs to hold the felt. 8. The baffle was installed inside the drum and using 2 hex bolts to hold the baffle in. I added 2 washers since the hole was inlarged due to the baffle becoming loose and pulling through the metal drum. 9. Re-install the drum and push rear felt to the outside of the drum. 10. The front drum needs to be installed. Push the felt to the outside of the drum and check the rear felt to ensure it is still on the outsid of the drum. Install 4 hex screws to secure front drum holder. 11. Insatall lint catch unit with 4 additional hex screws. 12. Verify the lint collection panel lins up with the exhaust fan at the base. When units line up tighten all 8 hex screws. 13. Reinstall front cover panel by inserting panel on bottom clips and tilt up to the dryer. The top corners are gently twisted to the outside of the dryer to reattach to the spring clips. Use 2 hex screws to attach panel. 14. Re-attach plastic clips and 2 screws on side opposite of door hinges. 15. Re-attach door hinges with 2 screws. Cleck to ensure the door closes. 16. Check dryer operation.
All three baffles fell out of dryer drum; one by one in a week time span; of course the warranty expired in May of 2007. Figures!
Had to remove the dryer door and back top screws to access the drum. Once this was accomplished all that had to be done was to turn the drum by hand and replace each baffle and (two) screws each.
Door safety switch would not close keeping dryer from running
Shut off or unplugged dryer for safety.
Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.
After reading all the other repair stories on Partselect, by the way thank you all, I removed the door, then removed the two security hooks that hold the top secure. Then I removed the front panel. I then marked all the screws on the outer door and shroud so I could easily put it back together. I left the all the wires connected and set the shroud and outer door to the side and removed the drum belt and drum. Removed the spring off the idler arm, then using nutdriver, removed the screw that secures the idler arm to the motor. Assembled the new idler arm parts and reversed the process to put it all back together. If I would have replaced the idler arm assembly the same time I replaced the drum support rollers, I wouldn't have had to do this twice! But now I am an expert repair tech on this particular model.
remove bottom section under door 2 screws remove door 2 screws remove switch by squeezing tabs install 2 new female ends on wires supplied with switch . put switch back in plug in wires .
Removed front cover, removed old heating unit, installed new thermostat,heating coil inside the dryer and finally replaced the fuse in the front. The main complication was reaching the screws for the heating coil, not really complex.
Ordered the part..... waited a few days fro it to arrive, (it came quite quick considering). Sat down in my easy chair and assembled the knob and gave it to my wife to slip it on the dryer. Whew, I was beat.... hehe
Appliance dealer stated that usually timers did not go out and thermostats were most likely . Tried all and called repairman that did not show. Removed cover found burned gear in timer ordered. The part is easy to replace just change wires one at a time or take a digital pic of the wires.
Dryer continuously running, no timer advance, dampness indication stayed on "wet"
Took 3 screws out of the back of the back of the machine and tilted the control panel houseing forward. Slid the module free of it's track and unplugged the bundled wiring plug. Plugged new module, relpaced in is slot and put the control panel back in place
An underwire form a bra shorted the element burning it out
Knowing most mfgs. put prints under the conturo panal we started there. Diagonstics required a multi meter. The part was removed and the internet serched. My local parts center was more expensive and would have to order the part. I called Partselect found exactly what i needed. placed the order with 3 to 5 day ground. Fedex arived the next day. The new part was installed and the dryer smoke tested. The dryer works great.