2036574-1-M-Whirlpool-33002973-Screw.jpg
2036574-1-S-Whirlpool-33002973-Screw.jpg 2036574-2-S-Whirlpool-33002973-Screw.jpg 2036574-3-S-Whirlpool-33002973-Screw.jpg

Screw

PartSelect Number PS2036574

This screw is sold individually.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $5.35
  • You Save

    $.89
  • Your Price

    $4.46
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 9 reviews What's this?
1-9 of 9
 

12 of 14 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerFred from Blairstown NJ

Baffle broke off and needed to be replaced

we replaced the baffle by removing the broken baffle. There were two screws holding it in place. Door and front panel of dryer had to be removed to accomplish this task. Quite an easy repair/replacement. Thank you for all your help PartSelect.com.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerRobert from Bulverde TX

Baffle became loose and sensor stop working

Repair is very simple, all I had to due was remove 4 screws on door and closing side door. Remove door and take off front panel. Then I spun baffle down to right side by motor removing 2 screws , replaced short baffle. the sensor wires are locate right there . Simple disconect of 2 spade wires , 2 srews inside and unit comes out. Please remember to disconnect power and door lifts up maybe 1/2 inch when disconnecting. The baffle worked fine the sensor fixed lights , but did not dry clothes to my satifaction. Good Luck

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerRon from Fresno CA

Loud noise - missing baffle

1 - unscrewed door
2 - made a mess because the directions did not work for my dryer
3 - figured it out = eventually
4 - popped loose the front panel
5 - unscrewed metal bars (that were holding the top down in the front)
6 - lift front like a hood on a car
7 - unscrew the rest of the front until the drum was loose and I could get to the felt strip
8 - glue new strip on where the old strip was = to the front and back plates that hold the drum
9 - put it back together :)

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerSandra from Germantown TN

All three baffles fell out of dryer drum; one by one in a week time span; of course the warranty expired in may of 2007. Figures!

Had to remove the dryer door and back top screws to access the drum.
Once this was accomplished all that had to be done was to turn the drum by hand and replace each baffle and (two) screws each.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers, Socket set

CustomerHeather from Pittsburgh PA

Incoming power hot lead broke loose from mounting block and short-circuited

First I turned off power at the service panel. Then, I pulled out the range and tried to remove the access panel. The screw which held the black lead from the incoming power to the range wiring terminal had broken loose from the mounting block. It had welded itself to the panel, so I had to pry it loose. I tried to reattach it to the mounting block, but the block was cracked.

I turned on power at the service panel and used my digital multimeter to test the AC voltage of the receptacle to make sure it fell within the correct limits.

When the new mounting block and power cord arrived, I removed the screw that held the broken mounting block to the back of the range. Then, I used a screwdriver to remove the leads that attached the old power cord to the broken mounting block and range wiring terminals. The screw and nuts which held the old black lead and range wiring terminal to the block were welded together. This was the most difficult part of the repair. I was able to back them off a little bit, but not enough to remove the range wiring terminal. While holding one end of the screw in the pliers, my Dad used the heavy duty cut off wheel on my Dremel tool to cut the screw in half and free the terminal.

Then, we reversed the process to attach the new wiring block to the back of the range, incoming power cord to wiring terminals and range wiring. We plugged it back in and had it working before my dinner party.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerPatricia from Mathuen MA

Broken baffle

I went on my laptop and typed in repairs to Maytag dryer - baffle and he said it was so easy. Dryer does not make any more noises and saved us probably $150.00. Your website is GREAT!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerElaina from Winter Garden FL

Baffle broke off drying some clothes

I actually followed the 5 tips from previous customers to fix the dryer. I removed the door then the screws on the other side and pulled the front open. Then spun the tub around to get to the screws attaching the baffle and removed and replaced with the new ones which attached the new baffle into place. It was very easy! Would have been faster but one of the screws holding the door on was too tight and almost stripped. Thankyou Part Select! Your diagrams and tips were very helpful! I will use you again!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Screw

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerGlenn from Bonham TX

Replaced two baffles

took off the dryer by remving two screws, then the front panel. Then removed the screws that held in the drum, pulled the drum out replaced the baffles then put it back together. It was easyer then I thought. It took less them 30 mins.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 469 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerKenneth from Purdy MO

Made loud noise when tumbling "all loads"

We went to Lowe's to look at a new washer/dryer set. We told the sales lady what our dryer was doing, she said she had that problem before and told us it was probably the rollers had gone bad. The next morning, 5 a.m my wife couldn't sleep so she took the dryer front off, pulled out the tumbler and found the rollers, the lady was right . My wife already had your web site pulled up on the computer so I could look to see what parts I needed. We called to order our parts, we were told it would be 2-5 days before they would get here, they were here the NEXT DAY!!! That was awesome!! I put the new roller on, my wife put everything back together, she turned the dryer on and.... it was so quiet we weren't sure if it was on so I opened the door and held the button to watch it turning, peacefully. Thank you all and the sales lady at Lowe's for saving us $1200. We did our repair with your parts and only spent $85.00.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-9 of 9