Others have described how to remove 4 screws and remove the front panel of the dryer. The problem I saw is that some screws broke off and fell inside while others remained on the separated baffle. The old screws that I found were 1 1/4 inch. The parts manual indicates a replacement screw that is 1 inch long and a number 10 width. One set of holes for the baffles has slotted holes. It appears that wear in the paint indicates movement before breaking off. My solution to the slotted holes was to use washers on the screws and to tighten the screws in the position where any force was not going to move the screws to the center position of the slots. The force of the separation caused the slotted holes to expand.
First removed front door 2 screws holding it to frame, then removed 2 screws holding front cover panel on tilt out front panel, used vac to clean inside, removed idler arm with pully attached, replaced with new parts when I did a test run still had a llitle squeek, the drum support wheel on right looking from front making some squeeking,I went back in removed part shaft had small rust spot cleaned with jewelers cloth lubed and wiped off, no more squeek I wish I had ordered new drum wheel when I ordered idler parts, then I could have done a complete overhaul now I know more I have never worked on a dryer before the drawings on the web site heleped a lot
We could not find directions for the brand that we have. First we took the back off, which we did not need to do. lift the top of the dryer, remove the front remove drum. Place belt on front of motor, wrap double belt around support on bottom of dryer, open the remaining belt and stretch around drum. Hold drum in place, replace front and top. Need at least 2 people, not at all intuitive.
With the parts in hand, and after disconneting power and shutting off gas line, I again removed the door, front panel and front tumbler frame to expose the blower wheel. I discovered that the blower wheel was not damaged, but that compressed pieces of lint and other items where stuck to the wheel. I removed the pieces and vacuumed the the whole thing clean, tested it, and the sound stopped. Since I had the unit open, I replaced the front glides by drilling out the old rivets, removing the old glides and then riveting the new glides in place. A very simple procedure overall.
Make sure you keep track of where the different screws go and keep them inside something so you don't lose them. I also used my cell phone to photograph various areas and screws for later reference.
shaft had become worn , making loud noise and also causing drum roller to wear prematurely.
first, i removed two screws at the bottom of front panel. then lifted from the bottom removing it. next, removed drum surround and drum. next , removed right roller and roller shaft. then installed new shaft, slide roller back on shaft. next reinstalled drum, drum surround and front panel. Now so quiet you can hardly hear it run, also my sister says it drys much faster.
First thing to do. . . . Unplug the machine. After that, remove the top 2 screws from the cover from between the washing machine and the dryer and remove cover. Then remove the 2 screws from the top of the front dryer cabinet, pull front cover out slightly and gently let it lay forward. From this point, you can look in and see the drum rollers. Behind the rollers on the roller shaft is a 1/2" nut. Use a 1/2" gearwrench to remove the nut, and pull the shaft with roller attached out forward. Use snap ring pliers to remove snap ring, take off old roller with bushings, and replace with new. To re-install shaft with new roller, you will have to lift the drum slightly to give yourself enough room. Re-assemble the front of machine (note: be careful of the wiring on the control panel, as some connectors may have pulled loose. Make sure they are all connected before replacing front of machine). Plug machine in and test it out. While you have the machine open, use a good vacuum cleaner and remove the lint that you will find inside the machine. Depending on how old the machine is, you should find quite a bit.
One of the drum support rollers was worn out resulting in a loud screeching noise when the dryer was in use.
Read the instructions included with the parts, removed the 2 screws on the front of the dryer. Removed a couple of wire connections and 4 screws that held the drum in place. Moved the drum enough to have access to the roller supports. I removed the nut from the back of the supports with a 1/2" wrench. Placed the new supports on the old support pins and reinstalled them. Put it all back together. Probably the most difficult task was getting the drive belt back on the drum correctly. I was done in just over 1 hour.
Pliers, Screw drivers, Wrench (Adjustable), Wrench set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
loud squealing noise
I had to remove the door first. Then the retaining brackets that hold the upper lid on. This also allowed removal of the front cover. After releasing the tension of the drum belt, I removed the drum and replaced the drum roller in suspect. Installation was reverse in order. Don't know why I waited so long to do such a simple job.
First I removed the two screws on the front panel that hold the element in place. I then pulled the element out about 3" and disconnected the two wires. Find out the roller broken. Place an order with Partselect from friend recommendation. Fast delivery, replace the broken roller, reverse the process and test the sound of the dryer. Very satisfied with the parts. Thanks!
After taking apart the machine (applianceaid.com has slideshows for most major appliances - very comforting and reassuring - highly recommended), I used a shop-vac to clean up all lint and dirt. After getting the retainer ring off the drum roller shaft (snap ring pliers highly recommended), I replaced the drum roller along with the glides which were completely worn through (rivet gun required). I reassembled the dryer to find that the drum wouldn't turn, so I placed another order for the other drum roller and replaced the belt too. Back in business.
Found out you shouldn't try to dry heavy hiking shoes in a dryer....it tends to break off plastic baffle.
The repair directions on PartSelct.com made this repair a piece of cake. Just removed screws holding door and front of dryer. With these removed it was a simple matter to detach top and get access to internal components. Two hex screws held baffle in place. Total repair took about 15 minutes, but while I was in there I cleaned out all the dust from inside of the dryer and heater unit. I also reversed door to make it easier to transfer clothes from washer. The instructions, detailed drawings and the quality of the part were all excellent. They had replacement to me in 1 day. Will definitely use PartSelect again.
Firts I had to take all the front parts off using a screwdriver and nutdriver then I loossen the belt to get the drum out then I had to use snapping ring pliers to remove the rollers and put the new ones in I cleaned the inside of the dryer then I put everything back in place. After all that I tested it and it worked really good it took me about an hour to do all that
