Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11741085
This part moves the clothes around inside your dryer and helps to direct the flow of hot air during the drying cycle.
NOTE: Screws are NOT included.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
removed door, removed screws to lift top panel, removed screws that held old baffles, replaced with new baffles, took off front panel and cleaned out excess lint while I was in there.
Help other customers find the most helpful instructions.
Were these instructions helpful?
take 2 phillips screws out where door meets drier. remove door, set aside. take 2 phillips screws out on other side, set screws aside. remove front of drier by pulling on top left and right sides, front of drier will fall twards front of drier. when it touches the floor lift up on bottom. set aside for later. put new baffels in (you can see where the old ones went) put screws in from bottom 5/16nutdriver. tighten. put drier front back on . start at bottom , snap top back in on both sides. put two screws back on left side, put door back on and replace 2 screws ( door will not go on wrong) test and your done...
easy repair. Another person had placed a youtube video on it on how to open up the dryer to get to the baffle. Baffle purchased only came with baffle. Had to go to Ace hardware to buy screws. This travel time was 90 percent of the repair. Disappointed the package didn't come with all the parts, like screws. Screws cost me another 2.50 as had to buy 2 separate sets to see which ones were needed. Next time if you are not going to ship something that is assembled, e.g. needs screws, with screws. Let me know ahead of time.
we replaced the baffle by removing the broken baffle. There were two screws holding it in place. Door and front panel of dryer had to be removed to accomplish this task. Quite an easy repair/replacement. Thank you for all your help PartSelect.com.
I took out screws holding top to dryer & raised the top & proped it up to gain access to inside of the dryeeer drum. I then inatalled the new baffle & secured it with 2 screws. It would have been better if the part came with new screws.It was hard to determine which was the right screws for this application.
1 - unscrewed door2 - made a mess because the directions did not work for my dryer3 - figured it out = eventually4 - popped loose the front panel5 - unscrewed metal bars (that were holding the top down in the front)6 - lift front like a hood on a car7 - unscrew the rest of the front until the drum was loose and I could get to the felt strip8 - glue new strip on where the old strip was = to the front and back plates that hold the drum 9 - put it back together :)
The YouTube video on how to replace the baffels was excellent. After watching the video, it was a piece of cake.
Following the instructions I pulled off the door and front panel. After rotating drum so the broken baffle was at the bottom I used a socket to remove the two screws on either end. I removed the broken baffle and inserted the new baffle in its place. Reinserted the screws, front panel, and door. I do strongly suggest having the manual handy to view the steps. It's available in PDF format.
Removed Dryer Door and front face of dryer, total of 4 screws, turn dryer drum to position broken baffle screws, remove screws, install new baffle, attach front face of dryer and reattach dryer door. Time 15-30 min. total. Real easy. Thank You PartSelect. Maytag told me my part was no longer available, but I fold it at PartSelect.com.
Went to YouTube. Found video of a guy with one arm in a sling. He showed all how to do it. Was really easy- so I did it. Works great.
Found out you shouldn't try to dry heavy hiking shoes in a dryer....it tends to break off plastic baffle. The repair directions on PartSelct.com made this repair a piece of cake.Just removed screws holding door and front of dryer.With these removed it was a simple matter to detach top and get access to internal components.Two hex screws held baffle in place. Total repair took about 15 minutes, but while I was in there I cleaned out all the dust from inside of the dryer and heater unit.I also reversed door to make it easier to transfer clothes from washer.The instructions, detailed drawings and the quality of the part were all excellent.They had replacement to me in 1 day.Will definitely use PartSelect again.
Unscrewed door and front panel. Pulled and took the, off. Used standing flashlight to illuminate the area underneath the dryer barrel. Tried various tools to take out broken plastic remnants. Then, used small electric nutdriver to screw the tall baffle into place with newly purchased metal screws. Was a bit hard to reach and tight but finally worked once I found an appropriate tool and top.
I went on my laptop and typed in repairs to Maytag dryer - baffle and he said it was so easy. Dryer does not make any more noises and saved us probably $150.00. Your website is GREAT!
The easiest repair I've ever had to do. I checked U-tube and watched a video on how to take off the dryer door and top to get to the baffle, then switched out the old for the new. Put everything back together and it is working great! So easy my 12 year old can do this fix.
First, suggest that, if you're mechanically challenged, take pictures or write down the disassembly sequence you use. Took off the door, removed the front sub panel, then the shroud. When I noticed the wires to the moisture sensors, etc., I remembered to unplug the unit. Once all the screws and clips are removed, used a pry bar to prop up the top of the unit. This makes it much easier to get to the baffle screws from the outside of the drum. Removed old baffles and replaced with the new ones, vacuumed out the inside of the unit, and put it back together in about an hour. It took the parts about three business days to arrive, so it was time to do laundry by then!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.