There was a leak coming from the underside of tjhe washer.
It was really quite simple. I found out where the leak was coming from by taking off the front panel and running the washer through the drain cycle. PartSelect website was right on for what part I needed and delivered it promptly. The installation video from PartSelect couldn't have been more clear. I removed a few screws from the back of the washer and installed the new part in about 1 hour. All was good.
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
First I bought a Maytag spanner wrench on eBay, you have to have it. It was $12.00 including shipping. Then when the parts showed up the next day followed the video and had it done in just under an hour from gathering my tools and cleaning up. The video was perfect and I had no troubles what so ever. The quote from the repair services was $280.00 and I did it for less than $90.00
Washer would fill with water but would not do anything else.
Done a troubleshooting problem online. Figured out the problem and ordered the part. Removed old part installed new part and I am a female not that it should make a difference but some would say it does. Had the old part out and new part put in and it took me about 30 minutes. Washer now works like a new machine. Very pleased and proud of myself. The part was the lid switch assembly.
We were seeing leakage on any but the smallest load size - higher water levels were pushing the worn seal back, not a total seal failure.
Viewed the very helpful video on your website, that spelled out all the steps to follow. The key point is to not forget the spanner nuts are left handed threads - even after noting that from the video, started the removal in the wrong direction, then caught my error and moved on through the disassembly process. In my case, I took time to deal with a lot of soap buildup cleanup in the outer tub, and even cleaned and put rust inhibiting paint on a few spots to try to get a little longer life out of the old machine. This repair cost far less than replacing it, and should get us several more years of service.
Unhooked water and drain lines, Unplugged electrical. Removed the two phillips screws at the bottom of the front cover. Removed the Front cover. TIpped machine backwards at about a 45 degree angle using a 2x4 to support the machine. Removed the pump belt and the drive belt. Installed the old pump belt and the new drive belt. Loosened the 3 each 5/16" bolts holding the pump mechanism and moved pump to the left. Moved pump to right to tighten pump belt and tightened the left pump bolt. Loosend the one pump bolt and pulled the motor to the left to tighten the drive belt and holding in this position I tightened the pump screws, Pump belt was now looser than the drive belt. Ran washer and it worked perfectly.
Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.
Agitator motor burned out -- purchased new one through Parts Direct (parts still available) 4 bolts and plug and play wire harness and now runs like new.
This washer was purchased in the early 1980s and is different from the one in the video and other repair instructions. You can recognize this earlier model by the agitator design. It only has the 4 paddles that start at the bottom and does not have the auger design on the upper part of the spindle as the newer ones do. While I was able to get the agitator to pop off by threading thin ropes under it and using a four-foot board as a lever, that was the end of my successful efforts. Even with the special tool and a five pound hammer, the lock nut would not budge -- even after overnight soaking in WD40. Yes, I did recognize the reverse threading. My next attempt would have been to heat the lock nut with a butane torch, but I gave up at this point and purchased a new washing machine on my way to pick up the torch. Would be curious to know if anyone else has had success with this older model as I saw other differences in the design that suggested that it may not have been compatible with this kit.
Washer is 27 years old. The washer lid bumpers were just worn out with age. It has been in constant use all these years raising 4 children with no other service or repairs. It has a matching dryer with the same track record. What a testament!
Removed the front panel with a screw driver, removed the old bumpers with a pair of pliers, replaced the bumpers and replaced the panel. All was very simple and took no time. The video on your website was most helpful. Thanks
Started with removing 4 screws on the top of the control panel. Once open, I found the schematic taped to the top. I traced the wires and found the 2 wires to test. I unplugged them and attached the jumper wire. Turn on machine and it worked. Ordered the part( it came in in about 3 days. First disconnect the power. The micro switch is mounted with 2 screws, remove these and as you disconnect the wires , attach them to the new switch, put it back in place and reattach the screws. Test .
Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top back out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal. Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3
