Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LAT5004BGW

LAT5004BGW Maytag Washer - Overview

Get Parts and Repair Help for LAT5004BGW

If you know the washer repair part you need, you can browse the list of all parts on the LAT5004BGW, or you can search by name or part description. You can also find your part by where it is located on the LAT5004BGW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LAT5004BGW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$49.51

Mounting Stem/Tub Seal Kit

This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace t...

Order within the next 5 hrs and your part ships today!
$5.15

Screw

This screw is sold individually.

Order within the next 5 hrs and your part ships today!
$19.70

Lid Switch

This two and a half inch long lid switch is used for washing machines that do not have a tub light.

Order within the next 5 hrs and your part ships today!
$24.44

Lid Check Switch

This is used to start your washer once the desired water level is reached.

Order within the next 5 hrs and your part ships today!
$9.35

Rubber Foot Pad

This foot pad is just over an inch in diameter. It is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers.

Order within the next 5 hrs and your part ships today!
$3.91

Centering Spring

This centering spring is nine and a half inches long. It is a metallic spring.

Order within the next 5 hrs and your part ships today!
$7.60

Washing Machine Lid Hinge Ball

This washing machine lid hinge ball is well under an inch in diameter. These hinge balls are sold separately, though two are required per lid. This lid hinge ball is made of plasti...

Order within the next 5 hrs and your part ships today!
$5.15

Hose Clamp

Order within the next 5 hrs and your part ships today!
$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

Order within the next 5 hrs and your part ships today!
$45.89

Tub Bearing Kit

This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time.

Order within the next 5 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 428 of 438 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

Washer was dead and would not turn on

  • Customer: Suleman from Canoga Park, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 89 of 100 people found this instruction helpful
Well the washer died and would not turn on in the middle of a wash cycle. Absolutely dead. I disconnected it from power and opened up the front panel on which all the control switches and knobs are mounted. This is removed by unscrewing 4 screws at the top of the washer.

Checked the fuse, and found blown. Replaced the fuse, closed the panel and p... read more

The washer wouldn't start unless you slammed the lid shut.

  • Customer: Richard from Houston, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 65 of 78 people found this instruction helpful
I suspected the lid switch right away. Where I went wrong was in thinking that I had to get to it from below. After going to all the trouble of removing the front panel and detaching the top panel, I discovered that it was located inside the control section at the top of the appliance. It only took a few minutes to remove four screws and gain access to the o... read more