Models > GLTF1670AS0 > Instructions

GLTF1670AS0 Frigidaire Washer - Instructions

All installation instructions for GLTF1670AS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GLTF1670AS0
46-60 of 267
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Noise During Spin Cycle

  • Customer: Bernie from Point Roberts WA
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 7 of 8 people found this instruction helpful
Using a cordless drill and driver bit I removed the back cover, bottom front cover and top. I then removed the rubber bellowed hose connecting the soap dispenser to the rubber boot in front. This one was tricky to reinstall because the fastener for the hose is twisted steel wire that needs to be undone when reinstalling. It slid off easily enough but would not slide back on easily. There is a second small bellowed hose that connects the dispenser to the outer drum casing. This needs to be removed as well. It comes off easily and went back on easily. I used a one sided razor to cut the glue dots connecting the front boot to the washer door frame. After that I removed the belt from the motor and drum pulley by hand and then removed the motor mounting bolts using a ratchet and socket. This went smoothly. I now propped up the drum using 4x4 cutoff blocks to take the weight off the springs and shocks. I then removed to the lower upper plastic pins that hold the shock onto the plastic spin drum casing. I used a wooded block and a hammer to tap the pins out. Be sure to push in the lock on the tapered end of pin shaft. The second pin was a little more difficult to remove and required quite a bit of tapping to push it all the way through. I tried adjusting the weight on the shocks several times to make it easier to come out. The pin was slightly damaged by the time I got it out from hitting it. It went back in OK so I don't think the damage will cause any problems. Next I got someone to help lift the drum to release the weight on the springs and removed then from the top end. You need to remove the spring clamps that hold the spring down at the top end. I used a wrench to remove the bolt that holds the pullet on the drum shaft. The pulley was easy to pry off shaft by placing two flat screw drivers between the shaft and the bearing casing and twisting the screw drivers. Once the pulley was removed I turned the spin drum casing upside down and supported the outer casing with two stacks of 4x4 cutoff blocks. This would allow the stainless steel drum to be supported above the floor and drop freely as the shaft worked it way out of the bearing casing. Getting the drum shaft out of the outer housing bearing was the most difficult part of this whole process. The shaft was rusty and therefore did not easily slide through the two bearing casings. Before hitting the drum shaft to remove it from the bearing casing I put the washer and bolt back on the shaft to protect the shaft from hammer/mallet damage. I tried a mallet but it only moved the shaft part way and then it wouldn't slide further. I then used a 1/2" steel pipe cutoff as a punch seated around the pulley bolt to alloy me to use a hammer to beat the shaft out of the bearing casing. It required a tremendous amount of force to move the shaft. Once the shaft was removed from the old drum casing I spent some time cleaning the back of the stainless steel drum including using emery cloth to remove the rust from the shaft and polish it the best I could. Be sure not to damage the brass bushing that the rubber bearing seal rides on to prevent water leakage. Once the drum and shaft were cleaned up the reassembly process when smoothly I simply reassembled the washer in the reverse order or the disassembly. The shaft went into the new bearings snugly which I was pleased to see since the snug fit meant that the water would be sealed in and the drum would spin true. The hardest part was reattaching the large bellowed hose onto the soap dispenser because it require undoing the twisted steel wire clamp and getting it back together in a very tight space. I use a combination of a flat screw driving and a needle nose pliers to wrestle it back together. The finished job resulted in a very quiet smoothly operating washer which we expect will give us another 5 years of service.

locking mechanism spring broke

  • Customer: laura from willow creek CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
Watched video which was very helpful

Door lock switch plastic bits broke

  • Customer: Herbert from Amherst NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
The previous posts made it dead easy - remove screws at the back holding top in place; slide top back; remove screws holding door latch assembly; disconnect three plugs, and connect new part. Replace fastenings, done! Throw up hands and wait for the official time;)

Thumping vibration on spin cycle

  • Customer: Kerry from Pasadena CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 9 people found this instruction helpful
Remove the front lower panel. Remove the 4 plastic pins mounting the shocks using 1/2 inch short socket to hold the detent down as per included instructions. All plastic pins were stuck in place so used needle nose pliers to pull or push out. Lube the pins with grease before reinstall to help them go through the new shocks. Use the included lock nuts to lock the four legs in place as low as possible. Start the washer and level each leg while running so you can tell if the vibration is going away. Tedious method but worked.

pump quit working , washer was full of water!

  • Customer: ROBIN from BLOOMINGTON IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
first took off old pump off by removing 2 screws and removed 2drain hoses under front load washer with pair of pliers then put new pump on same as removal.

Washer would leak water out the bottom.

  • Customer: Larry from East Point KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 13 people found this instruction helpful
First I removed the two screws holding the front panel on and removed the panel. The hose is held on by two spring clips and a hose clamp. After getting those out of the way, I removed the damaged hose and slid the new one into place and fastening it down with the aforementioned clips and clamp.

right side tub mounting spring broke

  • Customer: Lisa from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
disconnected electric and water supply. removed back cover from front loading washer. removed two screws from spring end plate on the top of the washer. replaced old spring with new spring/insulators by lifting the tub and hooking the new spring on. replaced the back cover and top spring cover plate. reconnected water supply and electric. machine is working like it did before the spring broke. very easy fix. the majority of the effort was moving the washer around to get easy access.

crack in drain hose

  • Customer: mary from port jefferson station NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 11 people found this instruction helpful
First I went on-line and found a download for the parts catalogue which contains a schematic for the washer. After looking this over I could determine how to get the washer apart! After getting the front panel off, I disconnected the drain hose from the pump with a pair of water-pump pliers. As I pulled this hose out, water spilled out all over the floor, so I then cleaned that up. Next I connected the new hose and put the machine back together. This job would have cost me over $150 if I had called in a repairman. PartSelect saved me so much money, and I thank them so much!

drain pump stopped working

  • Customer: Robert from Camby IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 5 of 5 people found this instruction helpful
First, I unplugged the unit, then took out the hold down screw. Next I took off both snap rings and layed towels down. Pulled off both hoses. Finally reattached in reverse order. I did not have the problem of others with the snap rings they came off easy and went back on easy.

No hot Water to washing machine

  • Customer: Dominick from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
S/O Water , Removed front panel, removed screws from side panel water valve accessible. Removed screws that hold water valve, installed new valve reassembled washing machine.

Door latch broken

  • Customer: Steven from Pompton Lakes NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 9 people found this instruction helpful
It was done in five minutes! Piece of cake. I will definetly use your site in the future. We had a servir=ce plan with Sears. They are the worst ever...do not pay the money. You only get India for customer service, and they tell you they are coming, do not show, and when you call them they say there is no service tech in the area. You can not get to anyone who can help it theyu did not show twice! We ended up canceling the service, and to their credit they send us a refund. Funny thing about it, they showed up today and left a message on our door that noone answered...this is after they refunded us.

space

  • Customer: Alvin from Woodside NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 5 of 7 people found this instruction helpful
1. replaced (2) shocks, remove bottom cover 2. (1) spring and rib belt, used a wooden block to hold up drum , rolled out ld belt and rolled in new----remove top and rear covers after replaced same ---thanks..

Tub to pump hose leaking

  • Customer: Barbara from Los Angeles CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
From the front of the washer, I removed two sheet metal screws at the bottom of the access panel. The panel pulled off with a just a little effort due to the nylon inserts installed on either side of the panel that keep it in place. The tub-to-pump hose is located on the right hand side and easy to access. The hose includes a screw clamp and two tension retainer (?) clamps that need to be removed.Make sure to save them for the new hose! I used a phillips head screwdriver for the screw clamp and a pair of channel locks to remove the tension retainer clamps. The tension retainer clamps were easy to remove but tricky to put back on. There must be another tool used for them that I'm not familiar with. With just a little patience though, it's an easy enough repair for anyone to do.

Quickly fixed a dumb mistake.

  • Customer: Andrew from McFarland WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
After accidentally dropping a crystal clock (don't ask) near the open door of the front-loading washer, the plastic striker broke and couldn't be repaired. Without this part being functional, the washer won't start because the door can't be secured.

I ordered the new part, and it arrived quickly -- that's really the story here.

Replacing it meant removing two screws, pulling the damaged part off, slapping the new part in, and replacing the screws. My 4th grade daughter could have done this one -- wish they were all that easy!

I'm glad the part came so quickly. With a local supplier, it would have taken four more days.

Leaky Drain Pump

  • Customer: Darrin from Cedar Rapids IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
NO EXPERIENCE NECESSARY!!
Unplug electrical.
Remove lower front panel -2 screws.
Locate drain pump in front right .
Remove electrical wiring plug - press release clip.
Remove mounting to floor - 2 screws.
Remove two hose clamps - pilers.
Mount in new part - 2 screws.
Reattach two hose clamps - pilers
* be sure hoses are fully reattached.
Attached electrical wiring plug.
Attach front panel - 2 screws
Plug in the electrical and be proud of your accomplishment because you just saved a minimum of US$200.00. Congrats.
All Instructions for the GLTF1670AS0
46-60 of 267