Drum Vane

PartSelect Number PS417359

Also known as a Drum Baffle. Sold individually.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

  • Compare At

    $28.85
  • You Save

    $4.81
  • Your Price

    $24.04
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 4 reviews What's this?
1-4 of 4
 

11 of 13 people found this instruction helpful

Parts Used

  • Drum Vane

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customerjudd from jax FL

H2o leaking on final spin

drum vane had a hole in it replaced it using phillips screwdriver removed one screw ,pulled drum vane towards the door then pulled up replaced it reversing the procedure. It actually seemed to fix my leak during spin cycle

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 12 people found this instruction helpful

Parts Used

  • Drum Vane

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerEugene from Westbrook ME

Broken drum vane needed replacing

Front-loading Frigidaire washer made by Electrolux:
I removed the one phillips screw that secures the drum, but found the vane did not slide toward the front as I'd read it should. Nor was I able to squeeze the base to release it. I ended up using a rubber mallet and screwdriver to spring the snaps at the bottom of the vane. Once I had two of these on the same side out, I was able to slide the vane forward and remove it. Turns out there was a metal tab, part of the drum, bent into the vane so it couldn't slide for removal. I bent this tab down even with the drum surface, and the new vane slid in easily.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 16 people found this instruction helpful

Parts Used

  • Drum Vane

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerWilliam from Juliette GA

Cracked vane in washer

Removed (1) philips screw in toward back of vane (closest to rear of drum), pulled the vane forward to remove it, slid the new one in place, replaced the screw, and was done in less than two minutes. Piece of cake.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 10 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Socket set

CustomerPaul from Lewiston ID

Leak in pump seal & cracked drum veins (2)

Very easy - veins are held in with one screw, when removed just slide to front of the washer and lift out. Pump assembly is a remote unit complete with drive motor. Take 2 screws out of the water shield, then unplug power to the pump motor and the green ground wire. Slide a cloth under the machine at the area of the pump to catch the water when the hoses are removed. Remove the hose clamp from the rear of the pump and the clamp on the discharge hose. You may be able th remove the hoses now, but if not remove the two bolts that hold the pump to the washer base & then remove the hoses. When you have the pump out you have to change the mounting base to the new pump. Also you may have to rotate the new pump discharge side with the motor (instructions are included with the new pump) - mount new pump, attach hoses, clamps,wires and water cover. Install front door that was removed at the start - pump in in the front right corner after removing the access door in front.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4