Models > GLTF1670AS0 > Instructions

GLTF1670AS0 Frigidaire Washer - Instructions

All installation instructions for GLTF1670AS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GLTF1670AS0
61-75 of 287
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

drain pump stopped working

  • Customer: Robert from Camby, IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 5 of 5 people found this instruction helpful
First, I unplugged the unit, then took out the hold down screw. Next I took off both snap rings and layed towels down. Pulled off both hoses. Finally reattached in reverse order. I did not have the problem of others with the snap rings they came off easy and went back on easy.

space

  • Customer: Alvin from Woodside, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 7 of 11 people found this instruction helpful
1. replaced (2) shocks, remove bottom cover 2. (1) spring and rib belt, used a wooden block to hold up drum , rolled out ld belt and rolled in new----remove top and rear covers after replaced same ---thanks..

Door latch broken

  • Customer: Steven from Pompton Lakes, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 12 people found this instruction helpful
It was done in five minutes! Piece of cake. I will definetly use your site in the future. We had a servir=ce plan with Sears. They are the worst ever...do not pay the money. You only get India for customer service, and they tell you they are coming, do not show, and when you call them they say there is no service tech in the area. You can not get to anyone who can help it theyu did not show twice! We ended up canceling the service, and to their credit they send us a refund. Funny thing about it, they showed up today and left a message on our door that noone answered...this is after they refunded us.

Leaky Drain Pump

  • Customer: Darrin from Cedar Rapids, IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
NO EXPERIENCE NECESSARY!!
Unplug electrical.
Remove lower front panel -2 screws.
Locate drain pump in front right .
Remove electrical wiring plug - press release clip.
Remove mounting to floor - 2 screws.
Remove two hose clamps - pilers.
Mount in new part - 2 screws.
Reattach two hose clamps - pilers
* be sure hoses are fully reattached.
Attached electrical wiring plug.
Attach front panel - 2 screws
Plug in the electrical and be proud of your accomplishment because you just saved a minimum of US$200.00. Congrats.

Kenmore 417.41042000 Front loading washer shakes

  • Customer: Chris from Burtonsville, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
Paid $27 total for a shock kit to replace the 2 broken stock shocks. Replaced them. It turns out it was not the problem, but just a symptom of the spider bracket (mates inner SS drum to drive shaft) corroding and breaking causing the drum assembly to shake out of balance. Found out is a systematic problem with this model washer, and no matter what else you fix, this will break and kill it at some point. Piece of crap!

Washer would not spin or complete spin cycle

  • Customer: Jonathan from Littleton, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
E47 error code means control board or door lock. From reading other stories, I decided to try the door lock first since it is much cheaper. Frigidaire tech support was no help at all.

First I removed the "wire" and spring that hold in the rubber seal at the door.

Then I removed the 2 screws that hold the door lock in place.

Removed the door lock, unplugged the 3 connections, plugged the connections into the new door lock, screwed it back in and replaced the rubber seal and wire that holds it in place.

Runs fine now.

Water valve not shutting off correctly

  • Customer: Eric from Sebastopol, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
After the new replacement part arrived, I took off the complete back panel (after unplugging the electrical and shutting off the hot & cold water supply). I disconnected both hot & cold water hoses, unscrewed the 2 screws holding the water valve, unplugged the 2 electrical wires for the water valve sending unit, unclamped the outlet water hose. Then I reversed order with new water valve. Put everthing back together in about 20 minutes overall. I did also replace the hot & cold water supply hoses with a better quality hose. Works like new! Thank you very much.

leaking water inlet valve

  • Customer: Steven from Oklahoma City, OK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
removed the two 'lock down flanges' from the back of the machine, lifted the top from the front and slid it forward to access the valve. Removed the two electrical connections then the compression ring from the hose on the output side. Removed two screws holding the valve in place, then reversed the process.

I wish this valve was made of metal rather than plastic. I had to replace it because the threads were stripped. Here's the heads up. Make sure the fittings on your supply hoses are 'clean' or you'll mess up the plastic threads and not get a good seal.

Washer wouldn't spin clothes

  • Customer: Brian from Forest Ranch, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
First thought the problem was with the spin cycle, however it soon became clear it was the pump that wasn't draining the water that kept the spin cycle from doing it's thing. After hand-wringing a large load and shopvacing out the remaining water, I ordered the new pump, got it in two days, and did a quick change out and it works perfectly. During the removal of the rubber boot that connects the tub to the pump, the one thing I did discover was a yucky buildup of years of fabric softener which I couldn't break my wife from using. But, after showing, and more importantly, letting her SMELL the fungus/mildew in the sludge, I've finally broken her of the habit! Best bang for the repair buck so far.

The threaded male coupling on the water inlet valve is plastic and broke during moving.

  • Customer: Alan from Denver, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
I installed this part on a stackable washer-dryer unit. First, I removed the hoses (one had broken off already, damaging the cold water coupling). Using a nut driver I removed the screws on both L-brackets in back that help secure the dryer unit to the washer base. Then, I located 2 other screws securing the dryer to the washer base. These were fairly accessible in the recess where the dryer exhaust vent is located, directly above the water inlet valve. I removed both with a nut driver. I thought I would have to also unscrew 2 more screws on the other side of the dryer, but these were not accessible. So I lifted the side of the dryer I had unbolted to get to the water inlet valve. And voila! It lifted up. I placed a 2x4 on edge to keep the dryer tilted open. The inlet valve is attached to the back inside of the washer by a single screw on the Kenmore, which I removed with a phillips screw driver. Reaching inside the back of the washer, I disconnected the water hose by pinching the retaining clip with pliers. Then I pulled the electrical connections off the the hot and cold solenoids and the unit came out. The replacement unit was installed in reverse.

old pump was viberating so bad that the whole machine rattled

  • Customer: Ed from Irrigon, OR
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
Very easy, took off the lower front cover (two screws). Pump is on the right side up front. Took the two screws out that hold it down, unclamped the clamps inlet and outlet hoses. Put a towel under and around pump to catch water befor pulling pump out. Installed the new one in revers order.

2 shocks and one spring broke

  • Customer: Don from campbell, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
repair wasn't too difficult, hardest was raising the drum to engage the springs.

Steps I took:

remove the rear and front (bottom) covers. To remove the rear cover, I went ahead and took the hoses off. The bottom cover needs a good tug once the two screws are removed.

Once both covers were off, it was obvious what had to be replaced.
Pushing the notch on the shocks, removed both top and bottom pieces. Then I used books to lift the drum so that i could attach the new springs. Removed the books, installed the shocks from the top to the bottom.

Went ahead and removed the coin drop, cleaned it out, and reattached. Ran the washer two cycles to confirm the vibrations were gone. Loaded it up with towels (seemed to cause the worst vibs) and it was quiet.

Re-installed the covers and that was it.

Basket loose and banging around - both shocks broken

  • Customer: Christopher from Woodbury, CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
-Unplug machine and remove all water connections
-Remove back panel with power phillips screwdriver
-Removed some rectangular circuit box in the way of getting to one shock absorber (3 screws)
-Remove old shock absorbers with 1/2 inch socket (suggested in accompanying directions)- this took 2 minutes
-inserted new shocks as directed...this was the most difficult part, but used a hammer to bang into place.
-reinsert and screw down circuit box (or whatever it was)
-reattach back panel
-reestablish water hose connections
-plugged in and was in business
-had ordered a washer/dryer set for $1700 (at my parent's urging) and now can tell Sears to go pound sand!

Quickly fixed a dumb mistake.

  • Customer: Andrew from McFarland, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
After accidentally dropping a crystal clock (don't ask) near the open door of the front-loading washer, the plastic striker broke and couldn't be repaired. Without this part being functional, the washer won't start because the door can't be secured.

I ordered the new part, and it arrived quickly -- that's really the story here.

Replacing it meant removing two screws, pulling the damaged part off, slapping the new part in, and replacing the screws. My 4th grade daughter could have done this one -- wish they were all that easy!

I'm glad the part came so quickly. With a local supplier, it would have taken four more days.

Door strike broke

  • Customer: Chris from Vernon Hills, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
The store I bought the washer from was going to charge $150 service call and over $60 for the part. I searched on the internet and found what i needed at partselect.com. The part was under $7 and the shipping cost more than the actual part. 2 screws, 1 screwdriver and it was fixed. Thanks!
All Instructions for the GLTF1670AS0
61-75 of 287