Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wash Cycle Selection Knob had plastic teeth on the underside that stripped out with years of use.
I used a pair of needle nose pliers and a screw drive to remove the clip holding the knob on its shaft. The new knob came with its clip already in place, so it "popped" right on. I ordered the compression ring in error and it it was not needed
Popped the front off the washer by placing a towel under the screwdriver to prevent chipping the paint. Had to spent almost 45 minutes soaking up water that had leaked from pump. Must have been leaking for some time before enough leaked under washer and became visible, because there was a lot of rust build up. (1).Removed old pump by first un-pluging washer and them removing (2) connecting wires from pump. (3).Next use nut driver to loosen flex hose from washer. (not from pump). Loosen spring clamp from discharge hose , and slide up. (4) Using nut driver I removed (2) hex screws that held pump to frame, then removed pump and motor assembly. (5). Mopped up water with large (old) bath towels (6). Used hair dryer to dry area. (7). Used wire brush to brush away surface rust. then used small shop vacuum to remove this surface rust. (8). Used small brush to paint white rust-olem paint on rusted areas, used hair dryer again to help paint to dry, then gave it a second coat and again helped it dry. (9). I then removed flex hose from old pump assembly, checked it for cracks and finding none I attached it to new pump with existing spring clamp. (10). I then put pump assembly back inside washer, but did not attach with hex screws yet. (11). Re-attached the drain hose by sliding the spring clamp back down, making sure it is around the hose and discharge spout. (12). Reattach the flex hose to washer discharge spout. (13). Screw new pump and motor assembly unto newly painted frame. (14). Re-attach (2) wires to pump and motor assembly. (15). Plug washer back in and try filling it with some water, letting it go into the drain cycle to check for leaks. NOTE: You don't have to go through and entire wash cycle. Just use the dial to put some water in then move it to drain and /or spin to get the new pump and motor assembly going. I did this a couple of times and then did an entire load of clothes to ensure there were no leaks. After I was sure there were no leaks, I simply popped the front panel back on. My part cost a total of $64.00 including shipping, and it took me about 1 hour of my time. I checked with my local GE dealer and his cost would have been $98.00 for the part, and $85.00 for labor for a total of $183.00. I AM VERY HAPPY. Oh bye the way I had my part within 3 days of the order and that was with regular shipping. I will always use Parts Select from now on.
hub corroded away and left spin basket sitting on bottom of tub.
Biggest problem was getting old hub nut off. I had to remove it in pieces because it was corroded so bad.
Once hub nut was off it was a breeze to replace the parts after cleaning off the threads and shaft.
Reassembled in reverse order.. and ran.
I have to give accolades to PartSelect.. their customer service is second to none. i ordered the parts just before the Christmas holiday and they shipped them to my door in under 24 hours at no extra charge to see that I got them on time... THANKS!.. It sure helped.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
17 of 21 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud bang during spinning
Remove aggitator, disconect 4 support straps, pry off clips/ latches on top of drum. Remove small bolt that holds on the small plastic unit unto trans. That will give you access to the large bolt that holds the hub in place. This nut is on tight use a pipe wrench and adjustable wrench and TURN CLOCKWISE TO REMOVE - lock for direction on nut. Remove the bin gently and turn over to remove the small bolts that hold the hub in place. Installation is reverse of removal.
I had to take the washer outside since there was no room to work on it in the laundry room. The extra space allowed me to spread out the parts, use the garden hose to clean and have light enough to take digital pics of the wiring before I disconnected them to remove the upper panel.
Removing the upper retaining ring for the tub was simple with only 4 screws. The agitator pulled right up and out. The nut cover/agitator anchor removed easily with one bolt.
The tough part was the inner tub base hub nut that I could not get off. Another user had commented on how they had to chisel the nut off and that was the best advice. I used my air chisel on either side of the nut and it was pretty quick to get off - within 3 min. If I hadn't read that I wouldn't have ordered another nut to replace the one I chiseled off.
The diagrams and repair stories really made the difference. Cleaning and reassembling was done within about an hour - cleaning the 11 years of soap scum at least an hour total before and after replacing the parts.
Bought all of the parts to remedy this. It ended up being the top transmission seal/bearing which is not a replaceable part. I could see the shaft moving side to side. But the parts diagrams are not detailed enough to show that when assembled.
She led a good life.
My new side loader is SO MUCH BETTER AND INSANELY EFFICIENT. I highly recommend making the change if you need a transmission..
My husband was unavailable and already overloaded, so I took a screw driver and removed the front cover of the washer. After I discovered where the leak was coming from, I used a screw driver to remove one end of the hose and pliers to remove the other end. I went online, found the part and ordered it. It came in surprisingly fast. My husband put it back in about 5 minutes.
was a toss up between the water inlet valve OR the hose pressure switch....why spend more time...I invested in both the water inlet valve and the hose pressure switch and replaced them both....I have the machine torn apart....I spend $45 more dollars...now it's ALL done....and works like a charm...if I were to isolate the problem...I would say, now, the hose pressure switch...but, I am happy and machine probably has 5 plus, more years left...and life is good.
took it appart and found that the suspension rod was broken. went on line an ordered the parts. The parts arrived 3 days later. Installed the parts and the washing machine was working within a half hour.
water not shutting off when filling tub and over flowing
First figured out tool to use to remove outer covering on control area. Then unplugged units from electric wiring and replugged with new parts. Parts arrived in a very short time was very pleasantly surprised with the short turn around on ordering and recieving parts.