1766022-1-S-GE-WH02X10265-Split Ring
1766022-1-S-GE-WH02X10265-Split Ring 1766022-2-S-GE-WH02X10265-Split Ring

Split Ring

PartSelect Number PS1766022

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Leaking water.
  • Unusual Noise.
  • Pumps but will not spin.
  • Shakes and moves.
  • Will not agitate.
  • Compare At

    $4.50
  • You Save

    $.75
  • Your Price

    $3.75
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Hub Washer

Part Number 271511

$3.14
In Stock

Hub Nut

Part Number 271505

$7.45
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.1 / 5.0, 13 reviews What's this?
1-13 of 13
 

95 of 113 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerWayne from Saint Augustine FL

Tub seal leaked, rusted the transmission bearing which locked up

I followed the instructions in the GE Consumer Service Training Technician Manual Pub. No. 31-10008.

I also power washed the basket and tub before reassembly.

The tub seal comes with the transmission and brake assembly so it's not necessary to order another seal.

The agitator coupling kit contains a redesigned coupler and longer screw with new o-ring.

I bought the hub nut, split ring, tub bearing, agitator coupling kit and washer hub because these are all the parts that go on the transmission shaft. I felt it was best to spend a few dollars more to replace every part involved with the spin and agitation of the washer.

I used the channel lock and a hammer with a shortened handle to remove and replace the hub nut. Use caution as the nut is aluminum.

The entire job took 5 hours.

Help other customers find the most helpful instructions.

Were these instructions helpful?

48 of 64 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerJoe from Lucedale MS

The hub under the spinner basket broken/ deteriorated

Removed front cover, Control panel, top Cover, slasher unit, all very smiple stuff. the hub was broken and the spinner basket came right out. One half Hub attached to Spinner, Other half attached to Hub drive shaft. removing the Hub nut was the hard part. tried impack & socket, No luck. in removal. Had to usr Hammer & Chisel and bust Old Alum. Nut off. Clean up and replace parts. OK. Had to remove water pump and clear debree that went in pump when spinner Hub broke off . the spinner also bursted a crack in the outer poly tube when it cam apart.. Sanded the dmage area and Patched with a good coat of JB Weld. machine is working Like new. The parts all worked Great. the break down Chart was a great Help to get the right parts needed. Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

36 of 54 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)

CustomerMichael from West Babylon NY

Tub would not spin / motor was smoking

the hardest part was getting the hub nut off. You have no room for a big wrench, I ended up chiseling it off.once I got it a part I saw the transmission was leaking oil, I checked every thing else, every thing seemed fine. I read on this web site that a common failure was the hub, mine was not in the best of shape so I replaced it while I was in there.replaced tub bearing,washer hub, hub nut , retaining clip for clutch,ring split, transmission and tub bearing 1/2 and $250.00 later the machine works like new.The diagrams that give you the part numbers were very helpful in the reassembly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

22 of 24 people found this instruction helpful

Parts Used

Level of DifficultyVery Difficult

Time to do repair:More than 2 hours

ToolsScrew drivers, Socket set, Wrench set, Wrench(Adjustable)

CustomerMichael from Allentown PA

Bearing above brake plate on transmission unit failed, brske material broken up

First I removed the agitator. The shoulder screw on top of the air bell was almost disintegrated, but after soaking with penetrating oil and a large channel lock pliers I removed the shoulder screw. Next, the air bell required a bearing puller to remove it from the agitator shaft (with force application to the agitator shaft from above). After two days of soaking with penetrating oil, heating with a hot air gun, and countless attempts with a pipe wrench and sledge hammer the 1 11/16 nut was not moving. I drilled down along the flats of the shaft and dug out as much corrosion as I could and filled the cavities with penetrating oil. Next, I drilled down at an angle (so as not to gouge the centering taper of the spinner hub) into the nut in order to relieve some stress - no success. I ended up using a chissel ( blade and flat round ) to break pieces of the nut away which was quite brittle. After removing about 1/8 of the nut's top and tapered portion, it began to turn out with a pipe wrench. Next, the spinner would not lift out off the shaft, so I had to remove the entire tub and transmission assembly (but with the spinner basket attached) as instructed by the paper stored within the control panel. I removed the tub support bracket and motor assembly and the pulley off the transmission (pieces of the brake pad fell out). Using a 2X6 piece of lumber, I fabricated 2 semi circular pieces to fit within the 20 inch diameter of the spinner basket and secured their position with another piece of wood. I attached eye hooks to the wood and with rope,hung the entire assembly over an I beam with the transmission in the 5 gallon bucket and the tub suspended only about an inch above the bucket. I hammered on the agitator shaft until the tub and transmission fell the inch as it separated from the spinner basket. After this, it was just cleaning the areas receiving new parts. I did use a sealant around the new tub seal edges and bottom when assembling. Other than having to tap 1/4- 20 threads in the new transmission brake flange (new part had no threads in the holes) the reassembly went fine. I did have to retighten the new 1 11/16 nut after the first use because the new brake pad really stopped the basket from spinning, but the momentom loosened the nut after 3 loads of wash.

Help other customers find the most helpful instructions.

Were these instructions helpful?

17 of 19 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Wrench(Adjustable)

CustomerDave from Willcox AZ

Water leakage from the bottom of the tub through the shaft seal

Thanks to comments already summited to Partselect I was prepareed for the worst. Once I figured out that you remove the agitator assembly with a swift jerk I was able to access the lower portion of the tub. As others have found out the aluminum nut holding the inner tub can not be removed without a hammer and chisel. Once you get past that things go well. What is left is cleaning the components and re-assembling.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 19 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)

CustomerKevin from Dillon CO

Washer was leaking where the tranmission entered the tub

Based on other research, the location of the leak indicated that the main tub seal needed to be replaced. I took the washer apart before ordering new parts in case I broke other parts in the process and to be sure I could. I ended up having to cut off the Agitator Coupling and really marred up the hub nut. Those were the hardest 2 pieces to remove since they had corroded badly after many years of use. I had to use a pipe wrench and a hammer to remove the hub nut and a hack saw to get the agitator coupling off (air bell).
$68.00 and 2 hours later, the washer no longer leaks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 19 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsScrew drivers, Socket set, Wrench(Adjustable)

CustomerEric from Oak Harbor WA

Grind noise becoming worse

Used the repair instruction paper behind the washer control panel and used the online parts diagram. Also the online responces from other customer repairs gave me the idea to take a small pipe wrench (with a sock over the bottom of handle) and tap it with a 10 lb sledge hammer to remove the alumium hub nut. *** It is a backwards threaded nut **** I did not know I was going the wrong way until I looked at the new nut and noticed it's reverse threaded!!! After that it was just taking everything apart and putting it back the way you found it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 14 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)

CustomerRichard from Spring City PA

Excessive agitator side movement

Bought all of the parts to remedy this. It ended up being the top transmission seal/bearing which is not a replaceable part. I could see the shaft moving side to side. But the parts diagrams are not detailed enough to show that when assembled.

She led a good life.

My new side loader is SO MUCH BETTER AND INSANELY EFFICIENT. I highly recommend making the change if you need a transmission..

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 11 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Socket set, Wrench set

CustomerDennis from Chilhowie VA

Transmission leaking grease

removed front cover the agitater then cover over large nut then large nut then inner tub then split ring and tub bearing then disconnected the hardware around the outer tub then replaced transmission then put back together in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 10 people found this instruction helpful

Parts Used

Level of DifficultyVery Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set

CustomerRoger from Port Saint Lucie FL

Water leaking through tub seal

First and foremost, the job would have taken 2 hrs instead of 8 hrs. The problem was that no one on the help instructions said that the Hub Nut had a LEFT HAND thread and suggested to just break the nut off. Well, after chiseling off most of the nut I drilled small holes through the nut and removed the nut pieces. However; I learned that I had damaged the transmission seal and had to buy a new transmission $183. Had I known this the job would have taken much less time and at a cost of about $50.
PS: The washer runs great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 9 people found this instruction helpful

Parts Used

Level of DifficultyDifficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)

Customershaobo from fremont CA

Washer barral spins with loud noise, turned out to be the worn wahser hub

1. take the machine apart, since the noise comes when the barrel is spining, I just watch for anything that contact to the axel.
2. without special tools, it was difficult to take off agigator, and a nut (that tighthened lefthanded).
3. Once defect part found, seach online for the part supply to replace.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

Level of DifficultyDifficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)

CustomerJustine from Cardiff CA

Washer wouldn't spin, repairman said replace transmission.

Pretty much the entire machine has to come apart to replace a transmission. The thing to know that no one mentioned is that the hub nut is reverse threaded - that means righty loosey.
Even if I had known, I tried it both ways and I doubt I could have gotten it off without the chisel as the others also had to do. Split ring was also frozen in place by hard water and soap scum so had to break that cheesey piece of aluminum off also. If you are taking apart your washer, I advise ordering these 2 parts so you will have them after you destroy the old ones trying to get to the part you need to fix.

Thanks to parts select for the exploded diagram!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:More than 2 hours

ToolsScrew drivers, Socket set, Wrench set

CustomerJames from Colora MD

Very noisy in spin mode

a) remove front panel by depressing the 2 clips at the top in line with the lid b) remove the lid switch and 2 screws holding top on and remove top by tilting up SLIGHTLY and sliding to left. c) Remove agitator and by pulling straight up on it and remove adapter underneath d)remove 4 bolts holding 4 rubber straps to top of tub assembly, readily visible when top is removed. e) unplug motor wiring and disconnect pump and bleach hoses from tub f)while lifting up on tub, push down on each of the 4 suspension rods and disconnect them at bottom of tub ( this is the most difficult part, and to make it easier disconnect the rear rods first) g) tilt tub forward and remove tub assembly h) NOW, for the big nut that holds the spin basket in-- #1, it is LEFT HAND THREAD, so you will turn it to the right to remove it. #2, it is VERY TIGHT and requires a 1&11/16" spanner wrench (which I did not have) for removal. Instead, I used a 1&11/16 socket, an extension and an air impact wrench to remove and replace the nut. Assembly is reverse of removal and remember, that nut is ALUMINUM so be careful with that impact wrench when tightening it back up!I replaced the nut and split ring and cleaned the whole area thoroughly, and it greatly reduced the noise in spin mode. I did not replace the metal housing on the bottom of the spin basket, because it was $50 bucks. this probably would have eliminated all the noise, but my repair only cost $19 in parts, including shipping ,and the parts arrived in 1 day.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-13 of 13