Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Freezer hinge was worn
Shut off water and disconnected at factory joint at bottom hinge. Unplugged the electrical at the top hinge. Removed the door and installed new bottom hinge and cam assembly. Reinstalled the door and hooked water and electric back up. Part worked fine.
Was able to pull the door up to the normal position, then blocked in place with 2 2x4's. Easily removed the hinge assemble and the door closing cam, which had broken in two. bolted on the replacement parts in 10 mionutes and the door was a good as new: peice of cake!!!
Removing gasket by pulling it back to expose 1/4" screws and replacing with the new one was easy. What was a HORROR- was that the new gasket doesn't seal against the door properly, and door doesn't want to close at all. to remedy this we had to put packing tape along the outer portion of the gasket all along the door to hold it donw, in order for the door to close. This is "possibly" becuase I overtightended the screws that hold the metal brace that holds down the gasket. Don't make this mistake and if you do, packing tape is the answer.
When it was discovered there was a cooling problem in the refrigerator, I went to parts select web site and went through the troubleshooting section. Then I tested the defrost timer and the defrost element as directed by the web site. I then found out doing this, that is was the defrost timer. I ordered the part online and it was delivered THE NEXT DAY! I removed the bottom panel of the fridge, removed the screw holding the old timer, removed the wires, and reversed the procedure to install the new one. It has been 1 week, and everything is working great. Thank you PartSelect. I have since then recommended you to a relative who was having the same problem. Thanks again.
Lets start with the hard part: Convince wife to get a couple of her girl friends to go to a movie and see the Reader,after that visit a cafe or pub (remembered years ago the English Patient). Drove to get a six pack,removed the back panel-2 min, set a hair drier to position, had a couple beers , removed the defrost heater unit 1 min. replaced it 1 min. back panel1 min,enjoyed the rest of the afternoon,finished the beer Killed two birds with one stone Zoltan L Petho
turned off water supply, took screws out of bracket, then unhooked water lines. Installed water lines onto new valve, plugged it in then screwed bracket back onto fridge, turned on water and was back operating
Refridgerator quit cooling because the defrost element had burned out and the refridgerator coils were totally covered with ice.
I defrosted freezer. Removed cover from back of freezer. Removed screws from element disconected wires. I connected wires to new element installed screws and reinstalled cover.
Removed the cover for the evaporater coils and let them defrost. Then took the old heating element out by removing two screws on the bottom element and two screws on the top element. Unplugged it and removed it from the unit. Then repeated the reverse of the procedure, installing the new unit, no wires to splice only one plug and four screws.
Pretty much self explanatory.Removed drawer and anything on top of glass shelf.Remove two screws holding on slide.Replace with new slide.Repeat on other side.Replace shelf and drawer.
1. Unplug refrigerator or flip breaker to kill power to the refrigerator. 2. With hands, gently pull the bottom lip of the 3" X 11" face plate panel above the dispenser head. 3. Remove the 4 screws that are under the removed panel. 4. Tip the assemby down to reveal 2 plugs. 5. Gently pull the 2 plugs to disconnect. 6. Open the assembly to reveal the solenoid. 7. There are 3 screws at the base of the solenoid. The center screw attaches to the green ground wire. 8. Remove the three screws. 9. Observe: The bracket at the top of the solenoid unit tucks behind a 4th screw above the solenoid. You may need to loosen this screw to relesae the solenoid. 10.Unplug the yellow and red connector to the solenoid. It should not be totally free to remove. 11. Put the plunger into the solenoid. Note that the plunger has an opening to insert the white plastic trigger for the trap door. Make sure the trigger is inserted into this opening before reassembling. 12. Plug the yellow and red connector into the new solenoid. 13. Position the new solenoid to match the screw holes. The bracket at the top of the solenoid tucks under the 4th screw. Tighten as necessary. 14. Insert the green ground wire into the middle screw hole at the base of the solenoid and tighten. 15. Insert the two screws to either side of the ground wire and tighten. 16. Gently reconnect the two plugs. 17. Tip the assembly back into place making sure the trap door and hoses are lined up correctly. 18. Replace the 4 screws. 19. Snap the face plate back into place. 20. Turn on the power and give it a try!
I used other instructions provided by customers on the website. They were very useful.
This is the second time we replaced this unit. The first replacement failed within the one-year warranty period. I called customer service and they had a replacement part and refund for the previous part on its way immediately. Excellent service!
Repair was very simple. Removed refridgerator bottom back panel, about 6 or 7 screws. disconnected bad valve, installed new valve , connected water supply line and then reinstalled panel. Took about 15 minutes from start to finish.
Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.
crushed ice feature inoperative, broken pieces in water dispensed.
Found broken pieces of deflector in delivered ice. Removed dispenser, carefully disassembled it, marking fasteners, sprimgs, and levers. Local repaimen say no replacement part available, must replace entire ice maker @ $350. Found exact part in your online reference, ordered at price of $3.76, part arrived two days later--perfect fit, exactly same as original. Reassembled, and it works exactly like new. Family very happy. Good job!!!!!
Fresh Food section door made a click noise on closing
Since the cam riser was obviously broken I obtained a replacement. It also broke. The door hinge cam needed to be replaced also. To repair Remove the hinge cover using a #2 phillips driver. Than remove the Hinge using an 8mm socket. Turn the door upside down and, using an 8mm socket remoge the cam riser and the door hinge cam. Replace in reverse order. Be sure to inspect all parts and order all required.
