Models > CG206B-C > Instructions

CG206B-C Jenn-Air Cooktop - Instructions

All installation instructions for CG206B-C parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CG206B-C
46-60 of 96
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

to convert a cook-top stove with 2 burners and a side grill into a 4 burner stove.

  • Customer: Robert from Silver Spring MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Replacing the side grill burners was easy--lift off the grill covers and pull out the grill burners. Next, attach the new front and rear burners to the burner plate with 2 screws (the older version uses 4 screws) using a nutdriver. Place the 2 burner unit (now joined) into the 2 gas inlets (no screws necessary--just slip them over the tubes). Insert the grill pan over the burners and place the 2 burner grates over each burner. Done!

installed new fan switch for counter stove top

  • Customer: James from Port Republic VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
The only problem was the little push nuts that came with the new part were too small for the posts on the stove top. I had to go to hardware and buy some for about 10 cents that fit. Other than that, everything was great. Great service from this company!

Switch held on by crimp on washers.

  • Customer: Bob from Heflin LA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Broke both crimp on washers. Drilled two appropriate holes in a dowell rod, used these holes to hold the new crimp on washers. Then drove the washers onto the switch's built in pegs.

smell of a dead animal

  • Customer: Duane from Niceville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.

The painted finish on the pan for my range started flaking.

  • Customer: Burma from Section AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Called Parts select and they replaced it in two days.

Grill broken

  • Customer: Mary from San Francisco CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Unfortunately, the part that snap and lock into place are welded about half inch incorrect. Although it works, it does not fit comfortably.

Fan switch broken

  • Customer: Bettie from Ashland VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
First the power to the cooktop was turned off. Two screws were removed to be able to lift the fan switch holder. The old switch was removed easly because it fell apart. The nuts holding the part in broke as they were removed so they could not be reused. The new switch was put in place however the nuts were too small. I don't know what they were supposed to fit but not these screws. The part was super glued in place. It works perfectly.

Changing over from LPG to Propane

  • Customer: George W from Carlsbad NM
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 2 of 6 people found this instruction helpful
In oven I unscrewed orfice; replaced with new orfice. On stove top the people who make it sent a kit for $11.00, plus S & H. I installed it as per instructions.

Replace old dingy part

  • Customer: Henry from Vancouver WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Part provided quickly and accurately

FAN SWITCH POPPED/BROKE THROUGH THE HOUSING.,

  • Customer: Bill from Dayton NV
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
OK, HOWEVER, FROM WHAT I READ ON THE INTERNET THOSE WHO WROTE DOWN THEIR ADVICE AND EXPERIENCE REGARDING THIS PARTICULAR PART, EXPLAINED THAT THE PUSH NUTS WERE TOO SMALL TO ACCOMODATE THE STUDS. I TOO HAD THE SAME PROBLEM, AND THEREFORE HAD TO GET OTHER ONES AT THE LOCAL HARDWARE STORE. APPARENTLY THIS IS INHERENTLY A COMMMON PROBLEM. YOU NEED TO PROVIDE PUSH NUTS WITH A SLIGHTLY LARGER DIAMETER, SO THEY CAN BE PUSHED DOWN THE STUDS/PEGS.

All of stove top parts grungy/peeling/burnt out

  • Customer: Donna from Carlsbad CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
Replaced all 4 burners, grates, pans, middle grate and fan/light switch. No real "repair" except for the switch, which has two phillips screws to remove the little panel the switch is enclosed in. The fasteners holding the switch TO this panel were VERY difficult to remove, you have to destroy them to get them off! Once that is done, removed the wires from old broken switch, placed them on new switch (now attached to the panel) placed panel back in to position, replaced the two screws and DONE! It was all quite easy and the stove looks brand new now.

The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.

  • Customer: Martyn from Middletown OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

Fan switch was broken internally.

  • Customer: Charles from Santa Clarita CA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 1 people found this instruction helpful
After reading the other do-it yourselfers I knew it wasn't going to be an easy task. However, when I received my new switch I saw that the hook up and installation would be a snap. My only problem was removal of the old lock washers so I cut them off with my tin snips and once the new switch was attached to the plate I used a socket on the end of a three inch extension. I placed the socket over the new washer and gently tapped on the end of the extention until the washer was seated. It took about two or three taps on each washer and I was finished. Everything went pretty well. Total time to install was about ten minutes.

Needed to replace the grease filter!

  • Customer: Colette from Annapolis MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Followed the directions. Piece of cake!!

replace old parts

  • Customer: Raul from Tampa FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Nothing really. Only couple of screws to attach the bracket holding the front and back burners.
The other parts: filter, burner, pan, where just replaced.
All Instructions for the CG206B-C
46-60 of 96