Models > CG206B-C > Instructions

CG206B-C Jenn-Air Cooktop - Instructions

All installation instructions for CG206B-C parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CG206B-C
91-96 of 96
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

One burner knob melted and one had a broken "stem"

  • Customer: Joan from Egg Harbor WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pop off the old and on with the new. Took longer to open the plastic packaging each came in than to remove & replace old knob with new.

Burner was not lighting

  • Customer: Luciano from Hollister CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the pan and then the burner assembly. Used a nutdriver to remove the old front burner. Replaced with the new part, tightened it on, and tested the new burner. Worked first time. Extremely easy. It took less than 5 minutes to replace.

Nroken Burnner knob

  • Customer: William M. from Rock Hill SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Slide the knob onto the shaft.

Replace Grill Side with Burners because I never used the Grill

  • Customer: Don from Scott AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Very simple remove the Grill section and install the Burners no reworking of existing Unit is required

One set of burners would not ignite.

  • Customer: Brenda from New Market MD
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
This range is about 17 years old and the igniter on the left set of burners had failed in the first month of use. A warranty repairman came, made a big mess, marred the adjacent counter top, spent a lot of time badmouthing Jenn-Air and left without fixing the problem. We have been manually lighting these burners all this time. Now that I am retired, I have set about repairing everything I can get my hands on just to have things to do. I always did this when I was young but got too busy with career and family. One big help is doing things now is you can Google a problem, find parts and instructions how to make the repair which is much easier than all the research you used to have to do. This repair is easy but time consuming due to all the screws that you have to remove to get to the igniter and the controller in the back. Since one side worked I was confident that the controller was good but the problem was only the igniter on the left side. This range is a dual fuel unit and has a downdraft connection so sliding it out from the wall is also time consuming. First pull the breaker at the electric panel. Remove the bottom plate and disconnect the flexible downdraft connection. Hopefully, you have enough flexible gas line so you can slide stove out to reach the back without having to shut off the gas and removing the connection. Next you remove the grills and burners. Then you have to remove all the screws connecting the top of the stove. There are nuts and washers that surround the gas jets that you can remove to partially lift the drip pan so you can unscrew the old igniter and install the new one. Next remove the back and see where the igniter control is located. Disconnect the old wire, install the new wire in the guides and insert in the controller. At this point all you need to do is put everything back where it was. This does not take a lot of know-how just time and patience. It makes you wonder why an "expert" could not have done this easily.

Filter worn out, exhasut fan kept going off

  • Customer: John from Cayce SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete
All Instructions for the CG206B-C
91-96 of 96