Models > CG206B-C > Instructions

CG206B-C Jenn-Air Cooktop - Instructions

All installation instructions for CG206B-C parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CG206B-C
61-75 of 97
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.

  • Customer: Martyn from Middletown OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

Fan switch was broken internally.

  • Customer: Charles from Santa Clarita CA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 1 people found this instruction helpful
After reading the other do-it yourselfers I knew it wasn't going to be an easy task. However, when I received my new switch I saw that the hook up and installation would be a snap. My only problem was removal of the old lock washers so I cut them off with my tin snips and once the new switch was attached to the plate I used a socket on the end of a three inch extension. I placed the socket over the new washer and gently tapped on the end of the extention until the washer was seated. It took about two or three taps on each washer and I was finished. Everything went pretty well. Total time to install was about ten minutes.

Needed to replace the grease filter!

  • Customer: Colette from Annapolis MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Followed the directions. Piece of cake!!

replace old parts

  • Customer: Raul from Tampa FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Nothing really. Only couple of screws to attach the bracket holding the front and back burners.
The other parts: filter, burner, pan, where just replaced.

The fan switch broke

  • Customer: David from Traverse City MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
remove gas valve knobs, removed two screws holding trim plate on lifted plate removed wires replaced switch and reversed the prior moves.

Very easy

The paint begin popping of my original grill. My son had a friend that said that he could remove the old paint and repaint for me. Unfortunately in the shuffle of a motorcycle performance shop the grill was lost. I have been trying to get help from Jenn-Aire since March and they just kept saying th

  • Customer: Norma from Salisbury NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Very simple for me!!! Open the box, uncover the new grill and lay it in its place.


Thank you so much!

vent fan cloging up

  • Customer: JAMES from McALESTER OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
old filter fell into from removing and cleaning,
removed cover pulled out filter ,replaced it with new one.

Worn out stove top

  • Customer: Redona from Roseville CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
We replaced the burner grates, knobs, air filter and burner pan. Looks as good as new!

Old grease filter had hole wore through

  • Customer: Michael from Mountain Iron MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Pulled the old one out & inserted the new one. Less than five minutes.

Filter replacement.

  • Customer: Gerald from Maplefalls WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Remove and replace grease filter.

ordered a new filter for the exhaust fan

  • Customer: Marijo from Bennett IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
The filter came and it was bent out of shape on 2 sides. My husband carefully tried to bend it back into shape. It is very flimsy and is not made as well as the one that was being used that was probably several years old. I did not want the hassel of returning the filter and trying to get a new one sent.

The stovetop gas regulator kept clicking in off position.

  • Customer: Preben from Fox River Grove IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 4 people found this instruction helpful
The spare part came within two days after I place the order on line. I drew a simple wire diagram of the faulty switch-regulator. Shut off the power to the stovetop, before removing the four terminals on the faulty switch-regulator. I pushed the old regulator up from the center pin and replaced it with the new regulator. The next step was to reinstall the four wire terminals using my wire diagram. Final step was to turn the power back to the stovetop and test the new switch-regulator.

Change the Oil/Grease Filter

  • Customer: Yong from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

Burner wouldn't light.

  • Customer: Clark from Tifton GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Took out a couple of screws and put in the new part. PartSelect was fast and efficient. Highly recommended.

old yucky filter

  • Customer: Diane from Flower Mound TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Thanks, have been looking for a replacement for this dinosaur filter forever. It is great!
All Instructions for the CG206B-C
61-75 of 97