Models > CG206B-C > Instructions

CG206B-C Jenn-Air Cooktop - Instructions

All installation instructions for CG206B-C parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CG206B-C
76-90 of 97
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Fan switch would not turn off

  • Customer: Ralph from Manteca CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
Disconnect power cord first. I remove the air fan cover to get to the two screws which hold the fan switch and burner knobs. Remove burner knobs and and remove switch cover, disconnect wires to fan switch. Pry spring nuts off with screwdriver to get switch off. Pay attention to which way switch goes on so that it turns on in the right direction. Install spring nuts (they may look too small but they're not) using a deep small socket the size of the spring nuts tap the the socket with a small hammer and the nuts will be locked in place. Put everything back in place and your done.

rotten filter for down draft vent

  • Customer: Craig from Ashburn GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
How I did the repair is no consequence. The service of easily finding the part on your site is GREAT! and the shipping time more than reasonable! Thanks!

Downdraft switch on the top of the JennAir inkoperative.

  • Customer: Daniel from Fort Walton Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 3 people found this instruction helpful
I verified that there was current running to the switch.
Ordered a new switch,
Replaced the switch.
Had a little problem getting the oneway washers off the pegs but not much.
Saved the cost of a repair man and felt good about myself!

The paint had chipped and peeled on the inlet grill

  • Customer: Ann from Irvington NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
I lifted off the old grill and replaced them with the new ones. My stove top looks great again. If I could find them, I would like to replace the knobs to turn on the gas!

NEED KNOBS FOR ELECTRIC STOVE-TOP

  • Customer: JUDY from HACIENDA HEIGHTS CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I DID NOT HAVE THE MODEL NUMBER AND THOUGHT I PICKED THE CORRECT KNOB BY THE PICTURE. I SENT BACK THE KNOBS AND ONE OF MY KNOBS TO SEE IF THE COMPANY CAN MATCH.

one of my Jenn Air knobs melted (gas range top)

  • Customer: Gayle from Whitefish MT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
pried off the old knob with hubby's needle nosed Leatherman pliers and popped the new one on!

Holes in the air filter of our Jenn-Air grill

  • Customer: Janice from Ocala FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply pulled the old filter out and put the new filter in.

Broke original Knob

  • Customer: Robert from Tracy CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Hardest part of repair was ordering part. The knob arrived the day after my placing order. Not rocket science to replace burner knob.

Replacement

  • Customer: Barb from Holladay UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,

Burner knob replacement

  • Customer: Peter from Foster City CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Inserted new knob on to the stem... very difficult operation taking a great amount of skill. ;-)

Filter was very old and falling apart.

  • Customer: June S from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The grease filter was 20+ yrs old and the mesh was falling of the frame. I was very pleased to find this replacement filter (the first filter I received was damaged....placed a call to PartSelect and have a new one the next day). Can't beat service like that!! Thank you, June Patten

Range burner melted plastic jar and became clogged

  • Customer: Harry from Cambria CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Found the part number on an old box, ordered the part and it arrived next day. Installed easily and is working perfectly.

Worn out burner grates

  • Customer: Richard from Omaha NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Lift and replace. This was the only web site that gave a picture with the correct size of the grates I was looking for. All the other sites gave approximate sizes and universal part numbers instead of the vendor part number. That is why I bought it here. I didn't want to have to return the product because it was off just a bit.

burner knobs were melted beyond repair.

  • Customer: Thomas from Tucson AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced the old knobs with the new ones.

The original filter was decomposing each time I washed it

  • Customer: Sharon from Kenai AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.
All Instructions for the CG206B-C
76-90 of 97