61004754 Kenmore Refrigerator - Instructions

The only part I needed was the Valve assembly. I checked for frost and found none. I took out the Ice Maker and found it was in poor condition but working. I did put in a new one but with the same problem. I finally read the comments from your costumers and found one place that told about a leaky water valve that was letting water drip into the ice maker so slowly it froze and blocked the valve. So I put in a new valve and thawed the pipe and allis well. What made this job so easy was the costumers comments and the best was the one day delivery of the parts. Thank you for all your help.

Got online typed in Maytag repairs. Watched the repair video. At that point I removed the door assembly (5 screws total) saw the broken door. Ordered the part from Partselect. Part was delivered in 3 days and installation was a very easy process.Thanks for the help.

easy, followed instructions and installed new parts.

Watched the video and followed the instructions ... time to repair was slightly longer than expected due to the fact that my fridge had wood panels requiring removal. Still, the video was terrific since I am a visual type person.Part Select service was amazing ... ordered one day and the part arrived at my door the very next day. Had the same type of service on a previous repair to replace the ice crushing part of the ice maker. What a company!!! Thanks so much.

I shut the water valve and bled the pressure off by using the water dispenser. Removed the four screws that hold the cardboard backing on the unit. Unplugged the power cord, loosened the metal water supply fitting. Then I removed all three hose fittings and dried the drips with a towel. I pushed the electrical plugs off with a flat blade screw driver. Removed the bracket attachment screw and pulled the double valve out. The new valves came with a push-lock fitting for the plastic hoses so I pushed them into their sockets. Put the new valve in and replaced the attachment screw. Reattached the water supply line and the electrical connectors. I turned the water on and checked for leaks. replaced the cardboard backing, and plugged the power cord back in.

I followed the directions from the YouTube video, which were spot on correct! Loved it. No problems. I did have to wind the spring one more turn than it showed on the video, but that was easy to figure out. No problems!

I had to buy the ice dispenser solenoid AND door kit just to get the door kit. The little flapper door was all that needed repair. I followed the video and this was so easy.. anyone could do this repair. PartSelect made this small job easy. Many thanks. HBoykin

The home service repair through our utility company checked the refridgerator and then looked for parts. Their conclusion is the part was no longer available and we should "just reach into the icemaker when we want ice until we replace the refridgerator.) The refridgerator is a top of the line model and replacement cost is well over $2,000 so that wasn't a good option. So I checked PartSelect and found the part which I received in 3 days, installed it in a few minutes and we're back in operation!

Followed the video exactly. Replaced both valves in less than 1 hour. No more leakage. Very simple!

I unplugged the refrigerater, then proceeded to remove the three screws that hold the dispenser face in position. When I lifted the dispenser face out of the way, I removed the remaining two screws that held the dispenser actuator pad in place. I lifted the unit away and turned it over. No need to unplug any cables. I simply lifted the old pad away, replacing it with the new pad. I re-assembled everything in the order in which I took it apart. Plugged the fridge back in. Tested the new actuator. Problem solved!

I followed the instructions that came with the kit.

We put all the new parts in that came with this kit including the Solenoid. It was super easy. I have a home warranty which covered the refrigerator ice maker, however, it would have cost me $75 just to bring out a repairman and then it would have taken up my time to be around when he wanted to come out. Buying this part and doing the job ourself cost me less money AND time.

I followed the online video exactly, except that the video only showed replacing the switch. Replacing the rubber "pusher" was easy & obvious once the switch was exposed.

replacing the electric water valves was not to bad took about 30 minutes but still had low water pressure traced it to the filter housing had good pressure going in but low coming out so I removed the housing and found a rubber washer was restricting the water flow so I removed the washer ,put it back together and it worked fine

Removed dispenser unit, replaced solenoid and door support, and reassembled. Repair video on website was extremely helpful. Only needed door support but found it was easier to order and install the entire assembly with the new door. Item number PS2003478