Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11738839
This motor is a 2 speed, 1/2 HP, 120V, 60Hz.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the base, replace the pulley on the shaft (you may need to break or pry the old pulley off) install the new pulley making sure it is all the way up the shaft locking the tabs into the shat groove. Reinstallmotor to the base. To replace the belt, tilted the unit backwards to access the pulleys from the bottom and installed.Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.
Help other customers find the most helpful instructions.
Were these instructions helpful?
i removed the plastic cover.then i disconnected the harnest.i then removed the 2 screws and took the motor out. i took a hack saw blade and made a mark in the old pulley. i then took a screw driver and put it in the crack and tapped on it and the old pulley fell apart. i then put on the new pulley and reconnect the motor. i then reconnect the belt.my washer is working great.it was so easy and i save myself some money in the process.
I pull out the motor pulley and put the new one then put belt on. but looks like the water pump its bad and I will have to order from you. Your service its the best I ever had ordering and deliver A+++++
Removed the 2 screws on the front panel after unplugging the unit. Removed the 2 screws on the safety cover and removed the wiring coupling. Removed the 2 bolts that was holding down the belt adjuster. Fed adjuster around pully wheel after removing belt. Installed new motor and re-assembled in reverse of disassembly. Plugged in unit and tested motor. Unit still operating satisfactory. Wash about 5 loads everyday. Large family
Removed the control panel, top and front panels to access the motor. Removed the motor and inspected. The motor looked fine. Leaned machine back and remove the brake cover following the directions posted by others on this website. Discovered grease and grime on the friction brake, which did not look right. The grease must have slung off of the transmission shaft. Wiped the brake clean with a dry rag and put machine back together. Machine did not run, motor only hummed. I replaced the motor only and the machine now works fine. My feeling is the grease caused the brake to stick and every time the motor started up, the sticking brake put a strain on the motor. Over time this cause the motor to burn up. Machine is only 6 years old. Sounds like a design flaw.
I took the front pannel off just 2 scrwe was holdig the pannel,the motor was in ftont,4 bolt was holdig the moto,and it is very easy to change,
Obvious problem: belt destroyed. The plastic pulley on the motor was damaged beyond repair. Since you can't replace just the plastic pulley, you have to purchase another motor. The machine still would not spin. Checked the pump again. The bearings might be bad. Replaced pump; Success! washer works again. Total repair: belt $15.68, new pulley with motor $132.00, and new pump $80.00. Estimated cost to repair about $228.00. Time to troubleshoot. 1 hour, time to fix 1 hour; Total time in labor about 2 hours.
First I took the front shield off, then I took the motor off.
just took the front off and then took the old motor off and switched over about 2 parts from the old to the new and then put the new part on and then placed the front back on and it was ready to go
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.