Models > AAV1100AWW

AAV1100AWW Admiral Washer - Overview

Get Parts and Repair Help for AAV1100AWW

If you know the washer repair part you need, you can browse the list of all parts on the AAV1100AWW, or you can search by name or part description. You can also find your part by where it is located on the AAV1100AWW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for AAV1100AWW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.68

Drive Belt

This V-style drive belt is about 51" long and 3/8" wide. This part is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get we...

$4.05

Lid Hinge

This lid hinge in an inch and a half long and is used for some washing machines. It is all white in color and it is made entirely of plastic.

$4.75

Snubber Ring

$69.70

Drain Pump

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This is a redesigned part. The pump now mounts on to the base of the washer - no mounting plate needed.

$7.46

Lid Hinge Pin

$36.18

Transmission Pulley and Bearing Kit

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are not available separately - only available in this kit. A worn bearing causes slow or no spin.

$29.48

Suspension Springs - Kit of 6

$2.70

Screw

This screw is sold individually.

$2.70

Hose Clamp

$123.61

Motor with Pulley

This motor is a 2 speed, 1/2 HP, 120V, 60Hz.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The belt and pulley on the drive motor broke

  • Customer: Michael from Warminster PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 83 of 105 people found this instruction helpful
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the base, replace the p... read more

EXCESSIVE Banging, shaking and squeaking while on Spin Cycle

  • Customer: robert from simpsonville SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 63 of 66 people found this instruction helpful
1)Start with empty washing machine.
2)Disconnect Hot, Cold, Power and Drain lines
3)Move machine to open area, open top by popping 2 front retaining clips.
4)Remove Front panel, remove small clear water level hose at lower rear of tub.
5)Remove small Rear access panel, disconnect large tub drain hose from pump and drain into small contain... read more

bearing on water pump siezed

  • Customer: kevin from rochester NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 53 of 55 people found this instruction helpful
back panel,belt two hoses,three screws, $100 dollars for the part!! pump is a molded part with a bearing insertion, is made in USA ! I'm guessing around 7 to 10 dollar manufacturing cost. I'm thinking that kind of mark-up is only exceded by the pharmacutical industry. I'm looking to buy a used machine for parts!! read more