WRS26MR4JS1 Crosley Refrigerator - Instructions

Had to pry the old one from the cabinet. Had to work remaining piece evenly as to not crack the cabinet of the fridge. Not the best design on Frigidaire's part but it was fixable. Thanks for stocking every part under the sun.

Remove and replace broke items. Crisper pan was the easy, just take the old one out and put the new one in. , The slider on the crisper was easy, just pop it out and reinstall. The front ice container was unscrew the screws and remove and replace old with the new. And insert the screw back in. Of course common sense tells you to dump the ice out of the ice containter first. Make sure everything lines up

Removed old one inserted new one . 15 seconds was done

I simply pulled out the ice container and auger assembly and,after washing the new one, Iput the new one in and it worked immediately. It couldn't have been any simpler.

Initially, I traced the noise down to the evaporator motor area. I thought it was the fan blade so I ordered and changed it. Noise level better but still not good. Then I ivestigated problem area again. Removed the motor,discoverd that the motor shaft was loose /drifting which caused the "hummm" and uneven fan blade rotation. Orderd and installed new motor and all is good.

Realized Ice Maker was not getting water during it's cycle and suspected water valve based on other posts to this web site. My fridge is 9 years old and the tubes connecting the valve were plastic screw on type. The new valve did not have threads to accept the nuts. Turns out all I had to do was cut the nuts off and insert the water tubes into the valve which auto-locked the tubes to the valve. Ice maker now works great.

I removed the top hinge (3 screws), lifted the door up and off the bottom hinge, then removed/replaced the bottom hinge pieces (2 screws) while the door was laying on the floor. I set the door back on the bottom hinge and reinstalled the top hinge. It's very easy to align the door while tightening the top hinge. It took about 15 minutes. The popping stopped and the door works like new!

Pulled out the fridge from the wall, unplugged it, and turned off the water supply. Took off the cardboard backing at the bottom of the fridge. Cleaned the dust and gunk. Unscrewed the old valve. Unplugged the 3 electrical connections. Since the new fittings for the water lines were different, we unscrewed the old ones, lopped off the nipples, and inserted the ends of the water lines into the new connections (they were super easy - just push the line in until it clicks). Reattached the valve. Reattached the cardboard. Turned water back on, and plugged in the fridge. Our ice maker still didn't make cubes, though. So I took out the fill valve from the top rear of the fridge. It had a tiny piece of ice lodged in the bend of the back, right above where it connected to the water line. I rinsed it out, reinstalled, and now we have a full bucket of ice!!

problem still persists part did not fix problem. made repairs recommended per your site.

replaced ribon i have an enginers degree in electronics so it was pretty simple for me to just unplug the old cable and plug the new one in

I was very thankful for the video that popped up when I ordered the crisper support part. It described exactly how to remove the damaged support without further damaging the inside of my regrigerator. I had the supports out and ready to go when my new part arrived. It took two minutes to do it the way it was described in the video and it worked like a charm. Thanks for the great tutorial and for putting it in a place that was accessible. Parts arrived very quickly as well. I didn't order enough supports so I had to re-order and they came quickly also.

Great job. Part arrived before promised. Packaged well. And most important...I actually got what I ordered. A pleasure doing business with you. Gene Lucarini

removed the old one & put the new bin in

Turned off the water supply ,pulled the plug removed two screws to access theater lines the new valve body was a little different than the original I had to cut off the end of each hose and push them in to the new connections the hoses are size and color coded replaced the two screws put the water line on plugged it in and turned on the water checked for leaks twice and replaced the back cover

Open package slide new bins in. That easy